Model
| Built
| Phase
| Numbers
| Qty
| Notes
| Last modified
|
EMD GP30 ← →
| 1962-05
| 1a
| KCS 100-109
| 10
|
| 2022-03-15Revision history:
2016-02-27
- Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version)
2017-09-02
- Corrected minor line glitch on latches on first engine room door
- Revised coupler pockets
- Corrected mismatched hood seams behind conductor's side inertial air intake
- Revised center radiator fan (changed to cap-top instead of open-top)
2017-10-07
- Revised bottom hatches on hood ends
- Removed bottom hatch latch hooks on short hood
2019-07-31
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors narrowed by 0.75"
- Middle hood doors narrowed by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
2020-12-06
- Increased handrail thickness
- Revised radiator fans (48" fans)
2022-01-30
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts
- Corrected minor transparency glitch with front truck traction motor air ducts (right side)
2022-03-15
- Horn manifold and back cap dimensions
|
|
EMD GP30 ← →
| 1963-07
| 2a
| KCS 110-119
| 10
|
| 2022-03-15Revision history:
2016-02-27
- Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version)
2017-09-02
- Corrected minor line glitch on latches on first engine room door
- Revised coupler pockets
- Corrected mismatched hood seams behind conductor's side inertial air intake
- Revised center radiator fan (changed to cap-top instead of open-top)
2017-10-07
- Revised bottom hatches on hood ends
- Removed bottom hatch latch hooks on short hood
2019-07-31
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors narrowed by 0.75"
- Middle hood doors narrowed by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
2020-12-06
- Increased handrail thickness
- Revised radiator fans (48" fans)
2022-01-30
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts
- Corrected minor transparency glitch with front truck traction motor air ducts (right side)
2022-03-15
- Horn manifold and back cap dimensions
|
|
EMD GP38-2 ← →
| 1974-01
| 1b2
| KCS 4000-4009
| 10
|
| 2023-01-09Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator and dynamic brake fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Increased metal sand pipe diameter
- Air pipe vent valve (left front / right rear under walkway)
2021-01-09
- Fuel tank height and gap from underframe
2022-02-07
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2022-03-03
- Horn manifold and back cap dimensions
2023-01-09
- Long hood end seams
|
|
EMD GP38-2 ← →
| 1978-06
| 2a2
| KCS 4010-4011
| 2
|
| 2023-01-09Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-11-11
- Removed batten strip from rear of dynamic brake hatch (left side)
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator and dynamic brake fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Increased metal sand pipe diameter
- Air pipe vent valve (left front / right rear under walkway)
2021-01-09
- Fuel tank height and gap from underframe
2022-02-08
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2022-03-03
- Horn manifold and back cap dimensions
2023-01-09
- Long hood end seams
|
|
EMD GP40-2 ← →
| 1979-08
| 2b2
| KCS 792, 798
| 2
|
| 2023-01-09Revision history:
2019-01-21
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
- Revised exhaust stack
2020-11-11
- Removed batten strip from rear of dynamic brake hatch
2020-12-07
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator and dynamic brake fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Increased metal sand pipe diameter
- Air pipe vent valve (left front / right rear under walkway)
2021-01-09
- Fuel tank height and gap from underframe
2022-02-08
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2022-03-03
- Horn manifold and back cap dimensions
2023-01-09
- Long hood end seams
|
|
EMD SD40 ← →
| 1966-10 - 1966-12
| 1b1
| KCS 600-613
| 14
|
| 2022-03-21Revision history:
2017-10-08
- Corrected minor line glitch on latches on first engine room door
- Revised bottom flange of dynamic brake fans
- Removed extra bolt on exhaust stack housing
2019-01-18
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
2019-01-23
- Relocated dynamic brakes
- Revised exhaust stack
- Corrected error with 4th handrail stanchion from rear
2019-08-10
- Added missing grabiron ahead of right-side battery box
2020-11-05
- Corrected line glitch in fuel filler (left side)
2020-12-21
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator and dynamic brake fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
2021-01-10
- Fuel tank height and gap from underframe
2022-03-21
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Horn manifold and back cap dimensions
|
|
EMD SD70ACe ← →
| 2011-09 - 2011-10
| 2f
| EMDX 2100-2114
| 15
| 2100-2109 re# KCS 4130-4139; 2110-2114 re# EMDX 1201-1205
| 2022-03-30Revision history:
2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)
2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills
2017-11-11
- Relocated hole below handbrake wheel (right side)
2017-12-17
- Revised cables/pipes under back of cab (right side)
2020-12-22
- Increased handrail thickness
2021-01-11
- Fuel tank height and gap from underframe
2022-01-21
- Added missing portion of brake levers near brake cylinders
- Corrected line glitch above cab nose door (right side)
2022-03-30
- Coupler cut levers
- Corner handrail end plate attachment points
|
|
EMD SD70ACe ← →
| 2005-10 - 2005-12
| 2a2
| KCS 4000-4029
| 30
| HTSC trucks
| 2022-03-30Revision history:
2020-12-22
- Increased handrail thickness
2021-01-11
- Fuel tank height and gap from underframe
2022-01-21
- Corrected line glitch above cab nose door (right side)
2022-03-30
- Coupler cut levers
- Corner handrail end plate attachment points
|
|
EMD SD70ACe ← →
| 2007-08 - 2007-10
| 2d2
| KCS 4030-4059
| 30
| HTSC trucks
| 2022-03-30Revision history:
2020-12-22
- Increased handrail thickness
2021-01-11
- Fuel tank height and gap from underframe
2022-01-21
- Corrected line glitch above cab nose door (right side)
2022-03-30
- Coupler cut levers
- Corner handrail end plate attachment points
|
|
EMD SD70ACe ← →
| 2008-01 - 2008-03
| 2e1
| KCS 4100-4129
| 30
| HTSC trucks
| 2022-03-30Revision history:
2020-12-22
- Increased handrail thickness
2021-01-11
- Fuel tank height and gap from underframe
2022-01-21
- Corrected line glitch above cab nose door (right side)
2022-03-30
- Coupler cut levers
- Corner handrail end plate attachment points
|
|
GE AC4400CW ← →
| 1999-11 - 1999-12
| 2a1
| KCS 2000-2049
|
|
| 2022-11-11Revision history:
2017-02-18
- Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side)
2020-10-20
- Added X-panel under central air intake (left side)
- Added sideframe holes below cab sub-base
2021-01-04
- Increased corner handrail thickness
- Revised end handrail stanchions
2022-01-05
- Added numberboard latches
2022-11-11
- Cab door window height
- Coupler cut lever and pilot details
- Corner handrail and step bolts
|
|
GE ES44AC ← →
| 2011-12 - 2012-10
| 2f1
| KCSM 4760-4764, KCS 4765-4809
|
|
| 2022-11-29Revision history:
2019-08-12
- Corrected minor transparency issue in radiators (left side)
2020-01-14
- Revised grabirons behind cab (left-side)
- Revised wide handrail stanchions
2021-01-12
- Increased corner handrail thickness
- Revised end handrail stanchions
2022-01-09
- Added numberboard seam
- Cab door window height
- Corrected line glitch on right front / left rear traction motor air duct
- Added missing sight glass under right side radiators
2022-11-12
- Coupler cut lever and pilot details
- Corner handrail and step bolts
- Added missing truck brake piping (left side)
2022-11-28
- Corner step height
- Added AEI tag above left rear truck
|
|
GE ES44AC ← →
| 2013 - 2014-05
| 2f2
| KCS 4810-4829
|
|
| 2022-11-29Revision history:
2019-08-12
- Corrected minor transparency issue in radiators (left side)
2020-01-14
- Revised grabirons behind cab (left-side)
- Revised wide handrail stanchions
- Thinner side handrails
2021-01-12
- Increased corner and side handrail thickness
- Revised end handrail stanchions
2022-01-09
- Added numberboard seam
- Cab door window height
- Corrected line glitch on right front / left rear traction motor air duct
- Added missing sight glass under right side radiators
2022-11-12
- Coupler cut lever and pilot details
- Corner handrail and step bolts
- Added missing truck brake piping (left side)
2022-11-28
- Corner step height
- Added AEI tag above left rear truck
|
|
GE ES44AC ← →
| 2014-10 - 2015-07
| 2g
| KCS 4830-4869, KCSM 4870-4894
|
|
| 2022-11-29Revision history:
2020-01-14
- Revised grabirons behind cab (left-side)
- Revised wide handrail stanchions
- Thinner side handrails
2021-01-12
- Increased corner and side handrail thickness
- Revised end handrail stanchions
2022-01-09
- Added numberboard seam
- Cab door window height
- Corrected line glitch on right front / left rear traction motor air duct
- Added missing sight glass under right side radiators
2022-11-12
- Coupler cut lever and pilot details
- Corner handrail and step bolts
- Added missing truck brake piping (left side)
2022-11-28
- Corner step height
- Added AEI tag above left rear truck
|
|