Model
| Built
| Phase
| Numbers
| Qty
| Notes
| Last modified
|
EMD GP18 ← ← →
| 1960-01 - 1961-10
| 1
| RI 1329:2, 1333-1343, 1344-1353
| 12 + 10
|
| 2023-07-10Revision history:
2020-12-05
- Increased handrail thickness
- Revised radiator fans
2022-01-03
- Larger roof lift rings
- Added lift rings on short hood
- Removed grabiron behind rear fan
- Exhaust stacks
2022-03-21
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Corner step height increased by 2"
- Footboard height increased by 1.25"
- Revised coupler carrier / draft gear
2023-01-14
- Added toilet drain pipe behind front steps (right side)
2023-02-07
- Removed handrail stanchion top clamps
2023-02-16
- Fuel tank height
- Fuel filler
2023-07-10
- Moved latches under radiators from 2nd to 3rd door from long hood end (right side)
|
|
EMD GP18M ← →
| 1961-02
| 1
| RI 1256
| 1
| GP7 rebuild
| 2023-07-10Revision history:
2020-12-05
- Increased handrail thickness
2022-01-03
- Larger roof lift rings
- Added lift rings on short hood
- Removed grabiron behind rear fan
- Exhaust stacks
2022-03-21
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Corner step height increased by 2"
- Footboard height increased by 1.25"
- Revised coupler carrier / draft gear
2023-01-14
- Added toilet drain pipe behind front steps (right side)
2023-02-07
- Removed handrail stanchion top clamps
2023-02-16
- Fuel tank height
- Fuel filler
2023-07-10
- Moved latches under radiators from 2nd to 3rd door from long hood end (right side)
|
|
EMD GP18M ← →
| 1963-10
| 2
| RI 1238-1239
| 2
| F7A/F7B rebuilds
| 2023-07-10Revision history:
2020-12-05
- Increased handrail thickness
2022-01-03
- Larger roof lift rings
- Added lift rings on short hood
- Removed grabiron behind rear fan
- Exhaust stacks
2022-03-21
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Corner step height increased by 2"
- Footboard height increased by 1.25"
- Revised coupler carrier / draft gear
2023-01-14
- Added toilet drain pipe behind front steps (right side)
2023-02-07
- Removed handrail stanchion top clamps
2023-02-16
- Fuel tank height
- Fuel filler
2023-07-10
- Moved latches under radiators from 2nd to 3rd door from long hood end (right side)
|
|
EMD GP35 ← →
| 1965-04
| 2a
| RI 300-304
| 5
| No dynamic brakes
| 2023-10-25Revision history:
2019-01-18
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
2019-08-07
- Corrected line/crop issue at right of image
2020-12-06
- Increased handrail thickness
- Revised radiator fans (48" fans)
2021-01-13
- Fuel tank height and gap from underframe
- Fuel tank vent pipe (increased diameter, revised fittings)
- Handrail stanchions above fuel tank (left side)
2022-01-29
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP35 ← →
| 1965-05 - 1965-08
| 2b
| RI 305-333
| 29
| No dynamic brakes
| 2023-10-25Revision history:
2019-01-18
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
2019-08-07
- Corrected line/crop issue at right of image
2020-12-06
- Increased handrail thickness
- Revised radiator fans (48" fans)
2021-01-13
- Fuel tank height and gap from underframe
- Fuel tank vent pipe (increased diameter, revised fittings)
- Handrail stanchions above fuel tank (left side)
2022-01-29
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP38-2 ← →
| 1976-08 - 1976-09
| 1c1
| RI 4300-4305
| 6
|
| 2023-10-25Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Air pipe vent valve (right rear under walkway)
2021-01-09
- Air pipe vent valve (left front under walkway)
- Fuel tank height and gap from underframe
2022-02-07
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2023-01-09
- Long hood end seams
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP38-2 ← →
| 1976-09
| 1c2
| RI 4306-4314
| 9
|
| 2023-10-25Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Air pipe vent valve (right rear under walkway)
2021-01-09
- Air pipe vent valve (left front under walkway)
- Fuel tank height and gap from underframe
2022-02-07
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2023-01-09
- Long hood end seams
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP38-2 ← →
| 1976-09 - 1976-11
| 1c3
| RI 4315-4355
| 41
|
| 2023-10-25Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Air pipe vent valve (right rear under walkway)
2021-01-09
- Air pipe vent valve (left front under walkway)
- Fuel tank height and gap from underframe
2022-02-07
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2023-01-09
- Long hood end seams
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP38-2 ← →
| 1978-11
| 2a2
| RI 4356-4379
| 24
|
| 2023-10-25Revision history:
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised paper air filter housing and dynamic brake taper
- Revised roof fan hatch
2019-01-24
- Front left traction motor cables moved 2.25" rearward
- Front right traction motor cables and air piping moved 0.75" to 1" rearward
2020-12-08
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Air pipe vent valve (right rear under walkway)
2021-01-09
- Air pipe vent valve (left front under walkway)
- Fuel tank height and gap from underframe
2022-02-08
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2023-01-09
- Long hood end seams
2023-10-25
- Nathan P-series horn dimensions
|
|
EMD GP40 ← →
|
| 1a3
| LLPX 3203-3208, 3211
| 7
| ex-RI 374-381; additional variations in plow, class lights and horn
| 2022-02-04Revision history:
2019-01-18
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
2019-01-23
- Revised handrail stanchion spacing
- Fuel tank and air reservoirs moved 1" to 1.5" rearward
- Revised exhaust stack
2020-12-04
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Added missing pixel in left side frame above rear of fuel tank
2021-01-09
- Fuel tank height and gap from underframe
2022-01-29
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
|
|
EMD GP40 ← ← →
| 1966-09 - 1967-01
| 1a3
| RI 340-361, 362-381
| 22 + 20
|
| 2023-12-28Revision history:
2014-10-22
- Truck shape and casting logos
- Radiator fans (bottom rim edge and upper rim clips)
2016-10-12
- Fuel tank supports
- Cab sub-base ribs
2018-10-31
- Corrected minor line glitch on latches on first engine room door
2019-01-17
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
2019-01-23
- Revised handrail stanchion spacing
- Fuel tank and air reservoirs moved 1" to 1.5" rearward
- Revised exhaust stack
2020-12-04
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Added missing pixel in left side frame above rear of fuel tank
2021-01-09
- Fuel tank height and gap from underframe
2022-01-29
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
2023-12-28
- Nathan P-series horn dimensions
|
|
EMD GP40 ← →
| 1969-01 - 1970-04
| 2b
| RI 382-396, 4700-4719
| 35
|
| 2023-12-28Revision history:
2014-10-22
- Truck shape and casting logos
- Radiator fans (bottom rim edge and upper rim clips)
2018-10-31
- Corrected minor line glitch on latches on first engine room door
2019-01-17
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
2019-01-23
- Revised handrail stanchion spacing
- Fuel tank and air reservoirs moved 1" to 1.5" rearward
- Revised exhaust stack
2020-12-04
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Added missing pixel in left side frame above rear of fuel tank
2021-01-09
- Fuel tank height and gap from underframe
2022-01-29
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
2023-12-28
- Nathan P-series horn dimensions
|
|
EMD SD40-2 ← →
| 1973-12
| 1a2
| RI 4790-4799
| 10
| No dynamic brakes
| 2023-01-09Revision history:
2012-12-17
- Air reservoir size
2013-03-24
- End plates
2014-02-17
- Truck shape and casting logos
2014-10-22
- Radiator fans (bottom rim edge and upper rim clips)
2014-11-07
- Inertial air intakes (added ridge on top)
- Revised center axle shock strut
2016-04-14
- Revised steps
2019-01-22
- Relocated front hood seam resulting in revised hood proportions
- Front section of hood lengthened and blower duct widened by 1"
- Revised hood section under inertial air intake
- Gap from seam to middle hood doors shortened by 0.75"
- Middle hood doors shortened by 0.25"
- Increased height of walkway blower duct and bottom of hood doors
- Corrected seam at bottom corners of long hood
- Revised radiator intake grills and roof fan hatch
- Corrected minor line glitch on latches on first engine room door
- Revised exhaust stack
2020-12-18
- Revised side handrail stanchions
- Increased handrail thickness
- Revised radiator fan dimensions and spacing
- Fuel tank vent pipe (increased diameter, revised fittings)
- Air pipe vent valve (left front / right rear under walkway)
- Sand lines (larger pipe diameter, revised hoses)
- Adjusted height of center hinge of engine room doors
- Added missing line segment in traction motor cables above fuel filler (left side)
2021-01-09
- Fuel tank height and gap from underframe
2022-03-19
- Coupler cut lever and pilot details
- Corner handrail end plate / stairwell attachment points
- Revised ribs on blower duct
2023-01-09
- Long hood end seams
|
|
GE U28B ← →
| 1966-06 - 1966-08
| 2b
| RI 255-261
| 7
|
| 2023-01-20
|
|
GE U28B ← →
| 1966-10 - 1966-12
| 2c
| RI 262-281
| 20
|
| 2023-01-20
|
|
GE U30C ← →
| 1973-10 - 1973-12
| 2g1
| RI 4582-4599
| 18
|
| 2023-01-27
|
|
GE U33B ← →
| 1968-07 - 1968-08
| 2b1
| RI 290-299
| 10
| Flush intakes illustrated; replaced with corrugated intakes after delivery
| 2023-01-27
|
|
GE U33B ← →
| 1969-01
| 2b2
| RI 285-289
| 5
|
| 2023-01-27
|
|
GE U33B ← →
| 1969-05
| 2b3
| RI 190-199
| 10
| Some units had earlier left-side handrail stanchion spacing
| 2023-01-27
|
|