Undecorated Drawings - SSW
| Selected scales: |
1:18 Drawings
| Model | Built | Phase | Numbers | Notes | Last modified |
|---|---|---|---|---|---|
| EMD GP20 ← → | 1960-12 - 1961-01 | 1a | SSW 800-809 | re# 4030-4039 | 2023-07-10Revision history:
2020-12-05 - Increased handrail thickness - Revised radiator and dynamic brake fans 2022-01-03 - Larger roof lift rings - Added lift rings around dynamic brakes 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Corner step height increased by 2" - Footboard height increased by 1.25" - Revised coupler carrier / draft gear 2022-11-15 - Changed draft gear housing from M-375/MS-485 to M-380/M-381 2023-02-07 - Removed handrail stanchion top clamps - Adjusted handrail stanchion spacing next to short hood - Added missing section of front hood doors (right side) 2023-02-16 - Fuel tank height - Fuel filler - Added missing line segment on bottom front edge of generator room doors (right side) 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| EMD GP20 ← → | 1961-12 - 1962-01 | 1b | SSW 810-819 | re# 4040-4049 | 2023-07-10Revision history:
2020-12-05 - Increased handrail thickness - Revised radiator and dynamic brake fans 2022-01-03 - Larger roof lift rings - Added lift rings around dynamic brakes 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Corner step height increased by 2" - Footboard height increased by 1.25" - Revised coupler carrier / draft gear 2022-11-15 - Changed draft gear housing from M-375/MS-485 to M-380/M-381 2023-02-07 - Removed handrail stanchion top clamps - Adjusted handrail stanchion spacing next to short hood - Added missing section of front hood doors (right side) 2023-02-16 - Fuel tank height - Fuel filler - Added missing line segment on bottom front edge of generator room doors (right side) 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| EMD GP30 ← → | 1963-02 | 1d | SSW 750-759 | re# SSW 5000-5009 | 2023-10-25Revision history:
2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2023-10-23 - Nathan P-series horn dimensions |
| EMD GP35 ← → | 1963-12 - 1964-02 | 1a1 | SP 7408-7455; SSW 760-763 | re# SP 6520-6567, SSW 6500-6503 | 2023-10-25Revision history:
2017-10-16 - Added circular hatch on long hood end - Removed long hood number boards 2018-11-11 - Corrected minor line glitch on latches on first engine room door 2018-11-14 - Added circular vent on top of short hood 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2023-10-25 - Nathan P-series horn dimensions |
| EMD GP35 ← → | 1964-12 | 1b4 | SP 7700-7712; SSW 764-771 | re# SP 6597-6609, SSW 6504-6511 | 2023-10-25Revision history:
2017-10-16 - Added circular hatch on long hood end - Removed long hood number boards 2018-11-11 - Corrected minor line glitch on latches on first engine room door 2018-11-14 - Added circular vent on top of short hood 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2023-10-25 - Nathan P-series horn dimensions |
| EMD GP35 ← → → | 1965-02 - 1965-03 | 1c1, 1c2 | SP 7713-7720, 7721-7727; SSW 772-775, 776-779 | re# SP 6610-6617, 6618-6624, SSW 6512-6515, 6516-6519 | 2023-10-25Revision history:
2017-10-16 - Added circular hatch on long hood end - Removed long hood number boards 2018-11-11 - Corrected minor line glitch on latches on first engine room door - Revised blower duct (GP40-style: fewer bolts, edge seam) 2018-11-14 - Added circular vent on top of short hood 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2023-10-25 - Nathan P-series horn dimensions |
| EMD GP35 ← → | 1965-07 - 1965-11 | 2b | SP 7762-7782; SSW 780-781 | re# SP 6659-6679, SSW 6680-6681 | 2023-10-25Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2019-08-07 - Corrected line/crop issue at right of image 2020-01-18 - Added lift rings below radiator intakes - Removed rear numberboards - Added circular panels on long hood end 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2021-01-13 - Fuel tank height and gap from underframe - Fuel tank vent pipe (increased diameter, revised fittings) - Handrail stanchions above fuel tank (left side) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape 2022-11-08 - Fuel filler 2023-10-25 - Nathan P-series horn dimensions |
| EMD GP40 ← ← → → | 1966-01 - 1966-03 | 1a1, 1a2, 1a3 | SSW 7600-7607 | 2023-12-28Revision history:
2014-10-22 - Truck shape and casting logos - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-01-17 - Cab side mirrors and armrest 2016-10-12 - Fuel tank supports - Cab sub-base ribs (Except Phase 1a1) 2018-10-31 - Corrected minor line glitch on latches on first engine room door 2018-11-14 - Added circular vent on top of short hood 2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Revised exhaust stack 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Added missing pixel in left side frame above rear of fuel tank 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-08 - Fuel filler 2023-12-28 - Nathan P-series horn dimensions | |
| EMD GP60 ← → | 1990-03 - 1990-05 | 2c | DRGW 3154-3156; SSW 9665-9714 | 2022-12-11Revision history:
2013-01-26 - Blower duct, central air intake - Dynamic brake housing - Trucks - Fans 2013-03-05 - Corner handrails, pilot braces, rear end plate - Traction motor cables 2014-02-15 - Truck shape and casting logo 2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2014-11-15 - Moved rear lift ring from roof to side - Revised inertial air intakes 2015-08-31 - Removed flag holders 2019-08-08 - Revised center hood door spacing - Revised hood behind cab - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door 2020-12-15 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Revised radiator and dynamic brake fan dimensions and spacing 2021-01-12 - Fuel tank height and gap from underframe 2022-12-11 - Coupler cut levers - Corner handrail end plate / stairwell attachment points - Anticlimber and MU receptacle brackets | |
| EMD SD45 ← → | 1968-02 - 1968-06 | 2a3 | SSW 8964-8981 | 2022-12-11 | |
| EMD SD45 ← → | 1969-01 - 1970-01 | 2b1 | SSW 9052-9068, 9152-9155 | 2022-12-11 | |
| EMD SD45T-2 ← → | 1972-07 - 1973-03 | SSW 9157-9165, 9261-9301 | 2023-01-06Revision history:
2023-01-06 - Corrected minor sand line glitch above right rear truck - Fan hatches under radiators - Taller doors ahead of right-side radiator intake | ||
| EMD SD45T-2 ← → | 1975-03 - 1975-07 | SSW 9371-9404 | 2023-01-06 | ||
| GE B30-7 ← → | 1980-01 - 1980-04 | 2c | SSW 7770-7799 | 7700-7773 were early B36-7's | 2023-11-11 |
| GE Dash 8-40B ← → | 1988-07 - 1988-11 | SSW 8040-8074; GECX 8002 | 2022-11-14Revision history:
2015-01-05 - Radiator roof grill dimensions - Left-side fuel tank fittings - Dynamic brake roof panels 2015-08-07 - Removed right rear hood grabiron 2021-01-05 - Increased corner handrail thickness 2021-01-28 - Revised air reservoir height and brackets 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts | ||
| GE Dash 8-40B ← → | 1989-05 | SSW 8075-8094 | 2022-11-14Revision history:
2015-01-05 - Radiator roof grill dimensions - Left-side fuel tank fittings - Dynamic brake roof panels - Front anticlimber 2015-08-07 - Removed right rear hood grabiron 2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions 2021-01-28 - Revised air reservoir height and brackets 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts |
1:55 Drawings
| Model | Phase | Numbers | Notes | Accuracy |
|---|---|---|---|---|
| EMD GP20 ← → | 1a | SSW 800-809 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP20 ← → | 1b | SSW 810-819 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP30 ← → | 1d | SSW 750-759; SP 7400-7407 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP35 ← → | 1a1 | SSW 6500-6503; SP 6520-6567 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP35 ← → | 1b3 | SSW 6504-6511; SP 6597-6609 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP35 ← → | 1c | SSW 6512-6519; SP 6610-6653 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP35 ← → | 2b | SP 6659-6679; SSW 6680-6681 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP40-2 ← → | 2a1, 2a2 | SP 7608-7627; SSW 7628-7657 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP40-2 ← → | " | " | As modified | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| EMD GP40-2 ← → | 3 | SP 7240-7247; SSW 7248-7273 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP40-2 ← → | " | " | As modified | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| EMD GP60 ← → | 2a | SSW 9620-9634 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP60 ← → | 2b | SSW 9635-9664 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD GP60 ← ← → | 2c, 2d | DRGW 3154-3156; SSW 9665-9714; SP 9715-9794 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD45 ← → | 2a3 | SP 8935-8963 SSW 8964-8981 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD45 ← → | 2b | SP 8982-9051, 9069-9151 SSW 9052-9068, 9152-9155 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD45T-2 ← → | SP 9166-9260, 9302-9313; SSW 9157-9165, 9261-9301 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| EMD SD45T-2 ← → | SSW 9371-9404 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GE B30-7 ← → | 2c | SSW 7774-7799 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GE B36-7 ← → | 2c | SSW 7770-7773 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GE Dash 8-40B ← → | SSW 8040-8094 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: