
Undecorated Drawings - EMD GP38-2
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
EMD GP38-2 ← → | 1972-05 | 1a | BN 2078-2087 | 2023-01-09Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised radiator intake grills and roof fan hatch 2019-01-24 - Fuel tank moved 2.5" rearward - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1974-11 | 1b2 | BN 2088-2109 | 2023-01-09Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Fuel tank moved 2.5" rearward - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2021-03-08 - Front classification and platform lights 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-06 | 2c | BN (FWD) 2150-2154 | 2023-01-09Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2021-03-08 - Front classification and platform lights 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-11 - 1979-12 | 2b2 | CNW 4600-4634 | ordered by RI | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions |
EMD GP38-2 ← → | 1977-06 | 2a1 | CR 8163-8180 | 2023-01-09Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-03-14 - Revised anticlimber 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1978-05 - 1978-06 | 2a2 | CR 8181-8201 | 2023-01-09Revision history:
2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1978-07 - 1978-09 | 2a2 | CR 8202-8255 | 2023-01-09Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-03-14 - Revised anticlimber 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-05 - 1979-06 | 2b2 | CR 8256-8281 | 2023-01-09Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-03-14 - Revised anticlimber 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1975-07 | 1b2 | DTI 221-227, 1776 | 2023-01-09Revision history:
2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) 2016-10-19 - Corrected Nathan M3 horn 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-01 | 1a | (F.L.) LN 4050-4069 | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised radiator intake grills and roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← ← → | 1972-09 - 1973-09 | 1b2 | (F.L.) LN 4070-4099, 4100-4144 | 2023-10-25Revision history:
2018-01-14 - Added ridge along top of inertial air intake 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1973-03 - 1973-11 | 1b2 | (F.L.) SCL 500-555 | 2023-01-09Revision history:
2018-01-10 - Added rear Mars light - Changed front Gyralite to Mars light 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1978-06 | 2a2 | (F.L.) CRR 6000-6004 | 2023-01-09Revision history:
2018-01-14 - Corrected small transparency error under exhaust stacks 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-02 - 1979-04 | 2a2 | (F.L.) LN 6011-6030; SECX 3821-3823 | 2023-01-09Revision history:
2018-01-14 - Corrected small transparency error under exhaust stacks 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-04 | 2b1 | (F.L.) CRR 6005-6006 | 2023-01-09Revision history:
2018-01-14 - Corrected small transparency error under exhaust stacks 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-04 | 2b1 | (F.L.) AWP 6007-6008; GA 6009-6010 | 2023-01-09Revision history:
2018-01-14 - Corrected small transparency error under exhaust stacks 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1979-07 - 1979-08 | 2b2 | (F.L.) CRR 6045; LN 6031-6044; SCL 6046-6050 | 2023-01-09Revision history:
2018-01-14 - Corrected small transparency error under exhaust stacks 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-03 | 2c1 | (F.L.) GA 6051-6052, SCL 6053-6054 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-10 - 1980-11 | 2c2 | (F.L.) SCL 6055-6065 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-04 | 1a | GMO 740-749 | 2023-01-09Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-08 | 1b1 | GMO 750-754 | 2023-01-09Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1978-12 | 2a2 | GTW 5812-5831 | 2023-01-09Revision history:
2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-14 - Revised anticlimber 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-01 | 2c1 | GTW 5832-5836 | 2023-01-09Revision history:
2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-14 - Revised anticlimber 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1977-05 | 2a1 | ITC 2001-2004 | 2023-01-09Revision history:
2014-02-16 - Truck shape and casting logos 2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1974-01 | 1b2 | KCS 4000-4009 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1978-06 | 2a2 | KCS 4010-4011 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-11-11 - Removed batten strip from rear of dynamic brake hatch (left side) 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1976-01 - 1976-02 | 1b2 | LIRR 250-271 | 2023-01-09Revision history:
2014-02-16 - Truck shape and casting logos 2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1977-03 | 2a1 | LIRR 272-277 | 2023-10-25Revision history:
2014-02-16 - Truck shape and casting logos 2014-10-23 - Radiator fans (bottom rim edge and upper rim clips) 2015-03-29 - Inertial air intakes (revised upper/lower ridge detail) - Rear steps (removed top step corner extension) 2015-08-25 - Revised end handrails above anticlimber (center stanchions moved in from the end) 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1972-11 | 1b2 | LV 314-325 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) - Front uncoupling lever 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-12 - 1974-08 | 1b2 | MKT 304-317 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1976-06 | 1c1 | MKT 318-321 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → → | 1972-05 - 1972-08 | 1b1 | PC 7940-8008, 8009-8018 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-08 | 1b2 | PC 8019-8039 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1973-05 - 1973-03 | 1b2 | PC 8040-8153 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2018-10-24 - Corrected glitch in right side cab sub-base door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1973-10 | 1b2 | PC 8154-8162 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2018-10-24 - Corrected glitch in right side cab sub-base door 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-07 - 1980-12 | 2c1, 2c2 | PW 2006-2008 | Phase 2c2 version illustrated; PW 2006 was Phase 2c1 | 2023-01-09Revision history:
2021-01-09 - Fuel tank height and gap from underframe 2022-01-05 - Changed air filter housing from early to late version (right side) 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
EMD GP38-2 ← → | 1982-09 | 3a | PW 2006-2008 | 2023-01-09Revision history:
2021-01-09 - Fuel tank height and gap from underframe 2022-01-05 - Changed air filter housing from early to late version (right side) 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1976-08 - 1976-09 | 1c1 | RI 4300-4305 | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1976-09 | 1c2 | RI 4306-4314 | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1976-09 - 1976-11 | 1c3 | RI 4315-4355 | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1978-11 | 2a2 | RI 4356-4379 | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1972-03 | 1a | SLSF 663-682 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised radiator intake grills and roof fan hatch 2019-01-24 - Fuel tank moved 2.5" rearward - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1972-11 - 1975-01 | 1b2 | SLSF 400-458, 683-699 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Fuel tank moved 2.5" rearward - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1976-11 - 1976-12 | 1c3 | SLSF 459-478 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Fuel tank moved 2.5" rearward - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1980-06 | 2c1 | SOO 4436-4443 | 2023-01-09Revision history:
2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1981-02 | 2c2 | SOO 4444-4450 | 2023-01-09Revision history:
2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1983-03 | 3b | SOO 4450-4452 | 2023-10-25Revision history:
2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions | |
EMD GP38-2 ← → | 1972-01 - 1972-03 | 1a | SOU 5000-5054 | High short hood | 2023-10-25Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions |
EMD GP38-2 ← → | 1972-12 - 1973-10 | 1b2 | SOU 5055-5103 | High short hood; SOU 5055-5058 were Phase 1b1 | 2023-10-25Revision history:
2020-01-11 - Revised speed recorder (conductor's side) 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions |
EMD GP38-2 ← → | 1974-01 - 1974-11 | 1b2 | SOU 5104-5162 | High short hood | 2023-10-25Revision history:
2020-01-11 - Revised speed recorder (conductor's side) 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions |
EMD GP38-2 ← → | 1972-12 | 1b2 | VTR 201 | 2023-01-09Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP38-2 ← → | 1974-10 | 1b2 | VTR 202 | 2023-01-09Revision history:
2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
See also: