Undecorated Drawings - EMD SD38-2
| Selected scales: |
1:18 Drawings
| Model | Built | Phase | Numbers | Notes | Last modified |
|---|---|---|---|---|---|
| EMD SD38-2 ← → | 1975-01 | 1b1 | CNW 6650-6659 | 2025-03-12Revision history:
2016-04-29 - Added truck details behind steps 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe | |
| EMD SD38-2 ← → | 1974-01 | 1a2 | EJE 656-659 | 2025-03-12Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe - Added angled handbrake chain housing on short hood | |
| EMD SD38-2 ← → | 1975-01 | 1b1 | EJE 660-664 | 2025-03-12Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe | |
| EMD SD38-2 ← → | 1975-11 | 1b2 | EJE 665-668 | 2025-03-12Revision history:
2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe | |
| EMD SD38-2 ← → | 1975-01 | 1b1 | LN 4500-4504 | 2025-03-12Revision history:
2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Changed horn from Leslie S-5T to Nathan P3 2023-01-09 - Long hood end seams 2024-06-10 - Nathan P-series horn dimensions 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe | |
| EMD SD38-2 ← → | 1979-06 | 2d2 | SLSF 296-297 | 2025-03-12Revision history:
2016-04-29 - Revised rear section of dynamic brake housing 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams 2025-03-12 - Updated phase number - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe - Corrected minor line glitch in front left / rear right MU hoses | |
| EMD SD38-2 ← → | 1979-06 | 2d2 | SLSF 298-299 | 2025-03-12Revision history:
2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2022-11-08 - Corrected line glitch on walkway behind cab 2023-01-09 - Long hood end seams 2025-03-12 - Updated phase number - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe - Corrected minor line glitch in front left / rear right MU hoses | |
| EMD SD38-2 ← → | 1973-04 | 1a2 | SP 2971-2976 | 2025-03-12Revision history:
2023-01-09 - Long hood end seams 2024-06-10 - Nathan P-series horn dimensions - Cab sunshade height 2025-03-12 - Added traction motor cable conduits above middle axles (where cables present) - Traction motor cable routing and cleats - Sand hose routing near steps - Added missing section of front right air pipe - Added angled handbrake chain housing on short hood |
See also: