Undecorated Drawings - EMD SD38-2
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
EMD SD38-2 ← → | 1975-01 | 1b1 | CNW 6650-6659 | 2023-01-09Revision history:
2016-04-29 - Added truck details behind steps 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1974-01 | 1a2 | EJE 656-659 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1975-01 | 1b1 | EJE 660-664 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1975-11 | 1b2 | EJE 665-668 | 2023-01-09Revision history:
2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1975-01 | 1b1 | LN 4500-4504 | 2023-01-09Revision history:
2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Changed horn from Leslie S-5T to Nathan P3 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1979-06 | 2b2 | SLSF 296-297 | 2023-01-09Revision history:
2016-04-29 - Revised rear section of dynamic brake housing 2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing and dynamic brake taper 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1979-06 | 2b2 | SLSF 298-299 | 2023-01-09Revision history:
2017-09-27 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2022-11-08 - Corrected line glitch on walkway behind cab 2023-01-09 - Long hood end seams | |
EMD SD38-2 ← → | 1973-04 | 1a2 | SP 2971-2976 | 2023-01-09Revision history:
2023-01-09 - Long hood end seams |
1:36 Drawings
Model | Built | Phase | Numbers | Notes |
---|---|---|---|---|
EMD SD38-2 ← → | 1973-03 - 1974-02 | 1a | BLE 870-879 | |
EMD SD38-2 ← → | " | " | " | As modified on delivery |
EMD SD38-2 ← → | 1975-01 | 1a | CNW 6650-6659 | |
EMD SD38-2 ← → | 1974-01 | 1a | EJE 656-659 | |
EMD SD38-2 ← → | 1975-04 | 1a | EJE 660-664 | |
EMD SD38-2 ← → | 1975-01 | 1a | LN 4500-4504 | |
EMD SD38-2 ← → | 1973-04 | 1a | SP 2971-2976 |
1:55 Drawings
Model | Phase | Numbers | Notes | Accuracy |
---|---|---|---|---|
EMD SD38-2 ← → | 1b | CNW 6650-6659 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD38-2 ← → | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |||
EMD SD38-2 ← → | Clasp brakes | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD38-2 ← → | No dynamic brakes | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: