Top header photo
 Trainiax logo
HomeNewContactLinks

Undecorated Drawings - EMD SD70ACe

Selected scales:


1:18 Drawings

Model Built Phase Numbers Notes Last modified
EMD SD70ACe
   
2007-11 -
2008-09
2e1 BNSF 9130-9165, 9168-9183, 9192-9194, 9230-9304 HTSC trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2008 2e1 BNSF 9195-9229 HTCR trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2009-02 -
2009-03
2e3 BNSF 9166-9167, 9184-9191, 9305-9329 HTSC trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
   
2012-09 -
2014-04
2f BNSF 9050-9129; MRL 4400-4408
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2011-08 2f EMDX 2012
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2011-09 -
2011-10
2f EMDX 2100-2114 2100-2109 re# KCS 4130-4139;
2110-2114 re# EMDX 1201-1205
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2005-10 -
2005-12
2a2 KCS 4000-4029 HTSC trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2007-08 -
2007-10
2d2 KCS 4030-4059 HTSC trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2007 2e1 KCSM 4060-4099
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2008-01 -
2008-03
2e1 KCS 4100-4129 HTSC trucks
2021-01-11Revision history:

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2011-02 -
2011-03
2f NS 1000-1024
2021-01-11Revision history:

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2011-10 -
2013-04
2f NS 1025-1064, 1075-1099
2021-01-11Revision history:

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2012-05 2f NS 1065-1074
2021-01-11Revision history:

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2014-02 -
2015-01
2f NS 1100-1174
2021-01-11Revision history:

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2005-01 -
2005-07
2a2 UP 8309-8423, 1982, 1983, 1988, 4141
2021-01-11Revision history:

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Removed seam at rear of cab (left side)
- Revised inverter cabinet grills

2017-12-17
- Removed angled brace behind end plates

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2006-05 -
2006-08
2c UP 8424-8520, 1989, 1995, 1996
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)
- First hood door on left side changed from bolted to hinged
- Revised truck casting text and air dryer location

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Removed seam at rear of cab (left side)
- Revised inverter cabinet grills

2017-12-17
- Removed angled brace behind end plates

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2007-02 -
2007-07
2d1 UP 8521-8620
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)
- First hood door on left side changed from bolted to hinged

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Removed seam at rear of cab (left side)
- Revised inverter cabinet grills

2017-12-17
- Removed angled brace behind end plates
- Revised cables/pipes under back of cab (right side)

2018-03-28
- Revised piping ahead of air reservoirs (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2008-05 -
2008-08
2e2 UP 8621-8670
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-12-17
- Removed angled brace behind end plates
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe
EMD SD70ACe
  
2011-08 -
2016
2f UP 8671-9061
2021-01-11Revision history:

2017-02-06
- Relocated traction motor cables above rear truck (left side)
- Minor revisions to cables above front truck (left side)
- Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side)

2017-09-19
- Revised truck traction pin (near center axle on trucks)
- Added minor truck details (bolts under axles and pins at radial-steering arm ends)
- Smaller radiator fan diameter and spacing, fans moved rearward
- Added missing section of air pipe behind front steps (left side)
- Revised inverter cabinet grills

2017-11-11
- Relocated hole below handbrake wheel (right side)

2017-12-17
- Revised cables/pipes under back of cab (right side)

2020-12-22
- Increased handrail thickness

2021-01-11
- Fuel tank height and gap from underframe

See also: