Undecorated Drawings - GMD SD40-2(W)
| Selected scales: |
1:18 Drawings
| Model | Built | Phase | Numbers | Notes | Last modified |
|---|---|---|---|---|---|
| GMD SD40-2(W) ← → | 1975-05 - 1975-07 | 1a1 | CN 5241-5261 | Builder's plate on all SD40-2(W) units: SD40-2 | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) - Added ditch light brackets 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | " | " | As modified | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | 1975-07 | 1a1 | CN 5262-5278 | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) - Added ditch light brackets 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | As modified | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | 1976-01 | 1a2 | CN 5279-5293 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | 1978-07 - 1978-10 | 1a3 | CN 5294-5313 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | 1979-12 | 1b | CN 5314-5323 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
See also: