Undecorated Drawings - ATSF
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
ALCO PA-1 ← → | 1946-09 - 1946-12 | ATSF 51B, 51L - 52B, 52L | 51B, 52B re# 63L, 64L | 2022-03-12 | |
ALCO PB-1 ← → | 1946-10 - 1948-03 | ATSF 51A-73A | 51B, 52B re# 63L, 64L | 2022-03-12 | |
EMD GP20 ← → | 1960-05 - 1960-07 | 1a | ATSF 1100-1124 | re# 3100-3124 | 2023-07-10Revision history:
2023-02-16 - Fuel tank height - Fuel filler - Added missing line segment on bottom front edge of generator room doors (right side) 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
EMD GP20 ← → | 1961-08 - 1961-12 | 1b | ATSF 1125-1174 | re# 3125-3174 | 2023-07-10Revision history:
2023-02-16 - Fuel tank height - Fuel filler - Added missing line segment on bottom front edge of generator room doors (right side) 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
EMD GP30 ← → | 1962-04 - 1962-06 | 1a | ATSF 1200-1234 | 2022-03-15Revision history:
2012-12-16 - Air reservoir size 2014-10-24 - Radiator fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2015-01-20 - Revised radiator intakes - distinction between Phases 1a-1c2 vs. 1d-2b 2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP30 ← → | 1963-01 - 1963-06 | 1e | ATSF 1235-1284 | 2022-03-15Revision history:
2014-10-24 - Radiator fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2015-01-20 - Revised radiator intakes - distinction between Phases 1a-1c2 vs. 1d-2b 2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1964-01 - 1964-02 | 1a1 | ATSF 1300-1315 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1964-03 - 1964-06 | 1a2 | ATSF 1316-1349 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | " | 1b1 | " | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1965-04 - 1965-05 | 1d | ATSF 1350-1383 | 2022-03-02Revision history:
2018-11-11 - Revised blower duct (GP40-style: fewer bolts, edge seam) 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1965-06 - 1965-11 | 2b | ATSF 1384-1460 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2019-08-07 - Corrected line/crop issue at right of image 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2021-01-13 - Fuel tank height and gap from underframe - Fuel tank vent pipe (increased diameter, revised fittings) - Handrail stanchions above fuel tank (left side) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP38 ← → | 1970-06 | 2b | ATSF 3500-3528 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised paper air filter housing and dynamic brake taper 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Corrected pipe overlapping bell 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Added missing pixel in left side frame above rear of fuel tank 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP38 ← → | 1970-08 - 1970-09 | 2b | ATSF 3529-3560 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised paper air filter housing and dynamic brake taper 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Corrected pipe overlapping bell 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Added missing pixel in left side frame above rear of fuel tank 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP39-2 ← → | 1977-11 | 2a1 | ATSF 3669-3682 | 2023-01-09Revision history:
2020-12-16 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-02 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP39-2 ← → | 1979-06 - 1979-07 | 2b | ATSF 3683-3695 | 2023-01-09Revision history:
2020-12-16 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-02 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP39-2 ← → | 1980-04 | 2c1 | ATSF 3695-3705 | 2023-01-09Revision history:
2020-12-16 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-02 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD GP40X ← → | 1978-06 | ATSF 3800-3801 | Locotrol-equipped | 2023-01-02 | |
EMD GP40X ← → | 1978-04 - 1978-05 | ATSF 3802-3809 | 2023-01-02 | ||
EMD GP50 ← → | 1981-02 - 1981-03 | 1a2 | ATSF 3810-3823 | Locotrol-equipped | 2022-11-30Revision history:
2020-12-11 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-11-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions |
EMD GP50 ← → | 1981-03 - 1981-04 | 1a2 | ATSF 3824-3839 | 2022-11-30Revision history:
2020-12-11 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-11-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions | |
EMD GP50 ← → | 1985-04 | 2b | ATSF 3840-3854 | 2022-11-30Revision history:
2020-12-11 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Moved 3rd stanchion from rear farther rearward - Corrected missing section from rear truck (left side) 2021-01-11 - Fuel tank height and gap from underframe 2022-11-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points | |
EMD GP60 ← → | 1988-05 | 2a | ATSF 4000-4019 | 2022-12-11Revision history:
2015-08-31 - Removed flag holders 2019-08-08 - Revised center hood door spacing - Revised hood behind cab - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door 2020-12-15 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Revised radiator and dynamic brake fan dimensions and spacing - Increased metal sand pipe diameter 2021-01-12 - Fuel tank height and gap from underframe 2022-12-11 - Coupler cut levers - Corner handrail end plate / stairwell attachment points - Anticlimber and MU receptacle brackets | |
EMD GP60 ← → | 1989-07 - 1989-08 | 2b | ATSF 4020-4039 | 2022-12-11Revision history:
2015-08-31 - Removed flag holders 2019-08-08 - Revised center hood door spacing - Revised hood behind cab - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door 2020-12-15 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Revised radiator and dynamic brake fan dimensions and spacing - Increased metal sand pipe diameter 2021-01-12 - Fuel tank height and gap from underframe 2022-12-11 - Coupler cut levers - Corner handrail end plate / stairwell attachment points - Anticlimber and MU receptacle brackets | |
EMD GP60B ← → | 1991-07 - 1991-09 | ATSF 325-347 | 2022-12-11Revision history:
2014-02-15 - Truck shape and casting logo 2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2014-11-15 - Moved rear lift ring from roof to side - Revised inertial air intakes - Corrected door latches 2015-07-25 - Front air reservoir piping 2015-08-31 - Removed flag holders 2019-08-08 - Revised center hood door spacing - Revised hood behind cab - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door - Corrected latch spacing on rear hood doors 2020-12-15 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Revised radiator and dynamic brake fan dimensions and spacing - Increased metal sand pipe diameter 2021-01-12 - Fuel tank height and gap from underframe 2022-12-11 - Coupler cut levers - Corner handrail end plate / stairwell attachment points | ||
EMD GP60M ← → | 1990-05 - 1990-09 | 2c | ATSF 100-162 | 2022-12-11Revision history:
2014-02-15 - Truck shape and casting logo 2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2014-11-15 - Moved rear lift ring from roof to side on Phase - Revised inertial air intakes 2015-07-25 - Front air reservoir piping 2015-08-31 - Removed flag holders 2019-08-08 - Revised center hood door spacing - Revised hood behind cab - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door 2020-12-15 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Revised radiator and dynamic brake fan dimensions and spacing - Increased metal sand pipe diameter 2021-01-12 - Fuel tank height and gap from underframe 2022-12-11 - Coupler cut levers - Corner handrail end plate / stairwell attachment points | |
EMD SD24 ← → | 1959-05 - 1959-07 | ATSF 900-944 | 2023-11-09 | ||
EMD SD40 ← → | 1966-03 - 1966-04 | 1a3 | ATSF 1700-1719 | 2022-03-21Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Corrected pipe overlapping bell 2019-01-23 - Relocated dynamic brakes - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2019-08-10 - Added missing grabiron ahead of right-side battery box 2020-11-05 - Corrected line glitch in fuel filler (left side) 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions | |
EMD SD40-2 ← → | 1977-11 | 2a2 | ATSF 5020-5027 | 123" short hood | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
EMD SD40-2 ← → | 1977-10 - 1977-11 | 2a2 | ATSF 5028-5057 | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1978-10 | 2a4 | ATSF 5200-5213 | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1979-04 - 1979-05 | 2b2 | ATSF 5058-5070 | Oscitrol light | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
EMD SD40-2 ← → | 1979-09 - 1979-10 | 2b2 | ATSF 5071-5108 | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1979-10 - 1979-11 | 2b2 | ATSF 5109-5124 | 123" short hood | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
EMD SD40-2 ← → | 1980-11 - 1980-12 | 2c2 | ATSF 5125-5140 | 123" short hood | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams |
EMD SD40-2 ← → | 1980-09 - 1980-10 | 2c2 | ATSF 5141-5169 | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1981-10 - 1981-12 | 2d2 | ATSF 5170-5192 | 2023-01-09Revision history:
2016-04-14 - Revised steps - redrawn steps with deeper angled sheet 2017-09-26 - Revised position of lift ring and flag holder at rear of long hood - Corrected minor line glitch on latches on first engine room door - Removed rear flag holder 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2020-12-17 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-17 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD45-2 ← → | 1972-05 | ATSF 5625-5646, 5648-5656 | 2023-01-09Revision history:
2020-12-22 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | ||
EMD SD45-2 ← → | " | ATSF 5647, 5657-5661 | 2023-01-09Revision history:
2020-12-22 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | ||
EMD SD45-2 ← → | 1973-05 - 1973-06 | ATSF 5662-5704 | 2023-01-09Revision history:
2020-12-22 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | ||
EMD SD45-2 ← → | 1974-05 | ATSF 5705, 5708-5711 | 2023-01-09Revision history:
2023-01-09 - Long hood end seams | ||
EMD SD45-2 ← → | 1974-05 | ATSF 5706-5707, 5712-5714 | 2023-01-09Revision history:
2023-01-09 - Long hood end seams | ||
GE B23-7 ← → | 1978-03 - 1978-05 | 1b | ATSF 6350-6363 | 2023-11-12Revision history:
2014-12-05 - Steps - Minor hood bolt details - Draft gear 2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions - Corrected underframe above rear truck 2018-11-21 - Revised air reservoir height and brackets - Changed air reservoir brackets to early style with vertical C-channel supports - Relocated rear traction motor cables closer to fuel tank - Added end-mounted fuel gauge on fuel tank 2019-08-12 - Corrected line glitch on left front/right rear axles (exposed axle caps only) - Removed stray pixel from #2 axle (left side) 2021-01-05 - Increased corner handrail thickness 2021-01-23 - Relocated fuel cutoff switch to within side sill 2021-02-11 - Pipe behind rear truck - Added sloped plate under frame behind draft gear - Fuel filler - Added safety valve to front air reservoir (left side) - Longer handrail stanchion in front of cab (right side) 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions 2023-11-12 - Added louvers on bolted panel under cab | |
GE B23-7 ← → | 1979-04 | 2b | ATSF 6364-6373 | FB-2 trucks | 2023-11-12Revision history:
2014-12-05 - Steps - Minor hood bolt details - Draft gear 2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions 2018-11-21 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2021-01-05 - Increased corner handrail thickness 2021-02-11 - Pipe behind rear truck - Added sloped plate under frame behind draft gear - Fuel filler - Added safety valve to front air reservoir (left side) - Longer handrail stanchion in front of cab (right side) 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions 2023-11-12 - Added louvers on bolted panel under cab |
GE B23-7 ← → | 1979-06 | " | ATSF 6374-6389 | Type B trucks | 2023-11-12Revision history:
2014-12-05 - Steps - Minor hood bolt details - Draft gear 2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions 2018-11-21 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2021-01-05 - Increased corner handrail thickness 2021-02-11 - Pipe behind rear truck - Added sloped plate under frame behind draft gear - Added missing end transoms on trucks - Fuel filler - Added safety valve to front air reservoir (left side) - Longer handrail stanchion in front of cab (right side) 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions 2023-11-12 - Added louvers on bolted panel under cab |
GE B23-7 ← → | 1980-04 | 2d | ATSF 6390-6404 | 2023-11-10Revision history:
2014-12-05 - Steps - Minor hood bolt details - Draft gear 2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions 2018-11-21 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2021-01-05 - Increased corner handrail thickness 2021-02-11 - Pipe behind rear truck - Added sloped plate under frame behind draft gear - Rear headlight and numberboards - Fuel filler - Added safety valve to front air reservoir (left side) - Longer handrail stanchion in front of cab (right side) 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE B23-7 ← → | 1984-12 | 3d | ATSF 6405-6418 | 2023-11-11Revision history:
2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions 2015-07-30 - Corrected front section of hood with narrower doors and vertical bolted straps (characteristic of Phase 3 Dash-7 units) 2016-12-30 - Added missing side sill hatch ahead of left rear jacking pad 2018-11-21 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2021-01-05 - Increased corner handrail thickness 2021-02-11 - Added sloped plate under frame behind draft gear - Rear headlight and numberboards - Added missing end transoms on trucks - Added safety valve to front air reservoir (left side) - Added underframe box / conduit behind top step - Longer handrail stanchion in front of cab (right side) - Added notch and square hole at top of bolted strip above door behind cab - Revised seams under door behind cab - Added drip rail over door behind cab 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions 2023-11-11 - Increased underframe height | |
GE B36-7 ← → | 1980-10 - 1980-11 | 3a | ATSF 7488-7499 | 2023-11-11Revision history:
2014-12-27 - Air reservoir piping 2015-01-08 - Central hood door spacing 2015-04-19 - Revised battery box cover dimensions 2018-11-21 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2020-02-11 - Revised air filter behind fuel tank (right side view) 2021-01-05 - Increased corner handrail thickness 2021-02-11 - Added sloped plate under frame behind draft gear - Rear headlight and numberboards - Added safety valve to front air reservoir (left side) - Longer handrail stanchion in front of cab (right side) - Added notch and square hole at top of bolted strip above door behind cab - Revised seams under door behind cab 2022-08-02 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions 2023-11-11 - Increased underframe height | |
GE C30-7 ← → | 1977-12 - 1978-06 | 1a | ATSF 8010-8057 | Hyatt wheel bearings shown; Timken bearings (as on later units) on approx. 8048+ | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Changed air reservoir brackets to early style with vertical C-channel supports - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Corrected height of wheel bearings - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE C30-7 ← → | 1978-10 | 1b | ATSF 8058-8063 | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Changed air reservoir brackets to early style with vertical C-channel supports - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2019-12-27 - Revised fuel cutoff switch housing 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions | |
GE C30-7 ← → | 1979-04 - 1979-05 | 1c | ATSF 8064-8098 | Adirondack trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE C30-7 ← → | " | " | " | Rockwell trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE C30-7 ← → | 1980-05 - 1980-06 | 2b | ATSF 8099-8122 | Adirondack trucks | 2022-08-03Revision history:
2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | " | " | " | Rockwell trucks | 2022-08-03Revision history:
2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler - Longer handrail stanchion in front of cab (right side) 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | 1981-05 | 2c | ATSF 8123-8132, 8134, 8136 | Adirondack trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-11-30 - Removed front louvers from right-side cab sub-base 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler cutout in side frame - Changed bolted strip / front hood doors to later-phase version - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | " | " | " | Rockwell trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-11-30 - Removed front louvers from right-side cab sub-base 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler cutout in side frame - Changed bolted strip / front hood doors to later-phase version - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | 1981-06 | 2c | ATSF 8133, 8135, 8137-8152 | Adirondack trucks Locotrol-equipped | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler cutout in side frame - Changed bolted strip / front hood doors to later-phase version - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | " | " | " | Rockwell trucks Locotrol-equipped | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Fuel filler cutout in side frame - Changed bolted strip / front hood doors to later-phase version - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | 1983-01 | 2e | ATSF 8153-8166 | Adirondack trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Corrected sand line glitch behind front truck (right side) - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab - Added drip rail over door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) - Added missing section of inner sand line brackets (under #3 and #4 axles) (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE C30-7 ← → | " | " | " | Rockwell trucks | 2022-08-03Revision history:
2018-11-22 - Revised air reservoir height and brackets - Added end-mounted fuel gauge on fuel tank 2018-12-01 - Removed brake lever pins from truck sideframe 2021-01-04 - Increased corner handrail thickness 2021-02-12 - Added safety valve to front air reservoir (left side) - Added notch and square hole at top of bolted strip behind front air intake (right side) - Rear headlight and numberboards - Corrected sand line glitch behind front truck (right side) - Longer handrail stanchion in front of cab (right side) - Revised seams under door behind cab - Added drip rail over door behind cab 2021-02-15 - Added missing section of pipe for handbrake chain (right side) - Added missing section of inner sand line brackets (under #3 and #4 axles) (right side) 2022-08-03 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE Dash 8-40B ← → | 1988-06 | ATSF 7410-7429 | 2022-11-14Revision history:
2015-01-05 - Radiator roof grill dimensions - Left-side fuel tank fittings - Dynamic brake roof panels - Front anticlimber 2015-08-07 - Removed right rear hood grabiron 2021-01-05 - Increased corner handrail thickness 2021-01-28 - Revised air reservoir height and brackets 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | ||
GE Dash 8-40B ← → | 1989-04 | ATSF 7430-7449 | 2022-11-14Revision history:
2015-01-05 - Radiator roof grill dimensions - Left-side fuel tank fittings - Dynamic brake roof panels - Front anticlimber 2015-08-07 - Removed right rear hood grabiron 2021-01-05 - Increased corner handrail thickness 2021-01-28 - Revised air reservoir height and brackets 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | ||
GE Dash 8-40BW ← → | 1990-10 - 1990-11 | ATSF 500-559 | 2022-11-14Revision history:
2017-01-25 - Revised cab side window size and location (slightly taller; moved slightly upward) 2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-01-05 - Added numberboard latches 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | ||
GE Dash 8-40BW ← → | 1992-03 | ATSF 560-582 | 2022-11-14Revision history:
2017-01-25 - Revised cab side window size and location (slightly taller; moved slightly upward) 2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-01-05 - Added numberboard latches 2022-11-14 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | ||
GE Dash 8-40CW ← ← → → | 1992-04 - 1993-07 | 1c, 1d, 1e | ATSF 800-866, 867-926 | 2022-11-18Revision history:
2017-01-25 - Revised cab side window size and location (slightly taller; moved slightly upward) 2017-02-13 - Removed clamps from middle handrail stanchions (above fuel tank) - Added seam to right rear of fuel tank - Removed erroneous line on right rear top step (some versions with tall steps) 2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-01-05 - Added numberboard latches 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | |
GE Dash 8-41CW ← → | 1993-09 - 1993-10 | 2b | ATSF 927-951 | 2022-11-18Revision history:
2017-01-25 - Revised cab side window size and location (slightly taller; moved slightly upward) 2017-02-11 - Removed clamps from middle handrail stanchions (above fuel tank) - Added seam to right rear of fuel tank - Removed erroneous line on right rear top step - Short hood grabirons 2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-01-05 - Added numberboard latches 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | |
GE Dash 9-44CW ← → | 1994-02 - 1994-03 | 1a | ATSF 600-649 | Early Hi-Ad trucks | 2022-11-12Revision history:
2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2017-09-30 - Removed incorrect line under bell 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-01-05 - Added numberboard latches 2022-11-12 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE Dash 9-44CW ← → | 1994-08 - 1994-09 | 1c | ATSF 650-699 | 2022-11-12Revision history:
2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2017-09-30 - Removed incorrect line under bell 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-01-05 - Added numberboard latches 2022-11-12 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE U36C ← → | 1972-05 - 1972-07 | 2f | ATSF 8700-8714 | 2022-03-21Revision history:
2018-12-20 - Added water level sight glass on right rear of hood 2020-01-25 - Revised hood doors behind cab (left side) - Corrected line glitch on brake chain pipe (right side) 2020-04-24 - Added walkway box (left side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions | |
GE U36C ← → | 1973-02 - 1973-04 | 2f | ATSF 8715-8735 | 2022-03-21Revision history:
2018-12-20 - Added water level sight glass on right rear of hood 2020-01-25 - Revised hood doors behind cab (left side) - Corrected line glitch on brake chain pipe (right side) 2020-04-24 - Added walkway box (left side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions | |
GE U36C ← → | 1974-05 - 1974-07 | 2g2 | ATSF 8736-8762 | Adirondack trucks | 2022-03-21Revision history:
2018-12-20 - Added water level sight glass on right rear of hood 2020-01-25 - Corrected line glitch on brake chain pipe (right side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE U36C ← → | " | " | " | Rockwell trucks | 2022-03-21Revision history:
2018-12-20 - Added water level sight glass on right rear of hood 2019-12-30 - Removed redundant truck casting lettering (left side) - Revised truck casting holes 2020-01-25 - Corrected line glitch on brake chain pipe (right side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE U36C ← → | 1974-11 - 1975-02 | 2h1 | ATSF 8763-8799 | Adirondack trucks | 2022-03-21Revision history:
2020-01-25 - Corrected line glitch on brake chain pipe (right side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
GE U36C ← → | " | " | " | Rockwell trucks | 2022-03-21Revision history:
2019-12-30 - Removed redundant truck casting lettering (left side) - Revised truck casting holes 2020-01-25 - Corrected line glitch on brake chain pipe (right side) 2020-12-31 - Increased corner handrail thickness 2021-02-07 - Fuel filler 2021-02-13 - Longer handrail stanchion in front of cab (right side) 2022-03-21 - Coupler cut lever and pilot details - Corner handrail and step bolts - Cab window gaskets - Horn manifold and back cap dimensions |
1:36 Drawings
Model | Built | Phase | Numbers | Notes |
---|---|---|---|---|
EMD FP45 ← → | 1967-12 | ATSF 100-108 | ||
EMD SD24 ← → | 1959-05 - 1959-07 | ATSF 900-944 | ||
EMD SD24 ← → | 1960-05 - 1960-07 | ATSF 945-979 | ||
EMD SD75M ← → → | 1995-03 - 1995-08 | 1c, 1d1 | ATSF 200-224, 225-250 | |
GE Dash 8-40CW ← → | 1992-04 - 1993-07 | 1c, 1d | ATSF 800-926 |
1:55 Drawings
Model | Phase | Numbers | Notes | Accuracy |
---|---|---|---|---|
ALCO PA-1 ← | ATSF version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD CF7 ← → | 1a | ATSF F-unit rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD CF7 ← → | 1b | " | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD CF7 ← → | 1c | " | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD CF7 ← → | 2a | " | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD CF7 ← → | 2b | " | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP30 ← → | 1a | ATSF 1200-1234 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1a1 | ATSF 1300-1349 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1a2 | " | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1b2 | " | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1d | ATSF 1350-1384 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 2b | ATSF 1385-1460 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP38 ← → | 2b | ATSF 3500-3560 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP39-2 ← → | DH, early ATSF version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP39-2 ← → | ATSF version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP39-2 ← → | ATSF version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP40X ← → | ATSF 3800-3809 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP50 ← → | 1a2 | ATSF 3810-3839 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP50 ← → | 2b | ATSF 3840-3854 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP60 ← → | 2a | ATSF 4000-4019 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP60 ← → | 2b | ATSF 4020-4039 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP60B ← → | ATSF 325-347 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP60M ← → | 2c | ATSF 100-162 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP7 ← → | ATSF Rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD40-2 ← → | 2a1 | ATSF 5020-5027 | 123" short hood | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | " | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2a1 | ATSF 5028-5057 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | " | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2a3 | ATSF 5200-5213 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | " | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2c2 | ATSF 5141-5192 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | " | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD45 ← → | 1a2 | ATSF 1800-1829 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD45 ← → | 1b1 | ATSF 1830-1889 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD45 ← → | 2b | ATSF 5590-5624 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD45-2 ← → | ATSF 5625-5661 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD45-2 ← → | ATSF 5662-5704 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD45-2 ← → | ATSF 5705-5714 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD75M ← → | 1c, 1d1 | ATSF 200-250 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SDF40-2 ← | ATSF SDP40F rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE B23-7 ← → | 1a | ATSF 6350-6363 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE B23-7 ← → | 2b | ATSF 6364-6373 | FB-2 trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE B23-7 ← → | 2b | ATSF 6374-6389 | Type B trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE B23-7 ← → | 2d | ATSF 6390-6404 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE B39-8 ← → | ATSF 7400-7402 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE Dash 8-40B ← → | ATSF 7410-7449 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE Dash 8-40BW ← ← → | ATSF 500-582 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE Dash 8-40CW ← → | 1c, 1d | ATSF 800-926 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE Dash 9-44CW ← → | 1a, 1c | ATSF 600-699 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: