Undecorated Drawings - CN
| Selected scales: |
1:18 Drawings
| Model | Built | Phase | Numbers | Notes | Last modified |
|---|---|---|---|---|---|
| EMD SD70I ← → | 1995-07 - 1995-11 | 1d2 | CN 5600-5625 | 2023-01-19Revision history:
2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points 2022-12-10 - Cab sub-base door proportions (right side) 2022-12-21 - Fuel tank length 2023-01-19 - Hood door and radiator intake height | |
| EMD SD70M-2 ← → | 2007-07 - 2007-11 | 2e1 | CN 8800-8849 | 2022-03-30Revision history:
2016-10-08 - Added missing rear platform lights on the hood end - Center hood door height - Large rear hood intake height 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Removed seam at rear of cab (left side) 2017-11-11 - Corrected minor glitch in front truck traction pin (left side) 2017-12-17 - Revised cables/pipes under back of cab (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
| EMD SD70M-2 ← → | " | " | " | as modified | 2022-03-30Revision history:
2016-10-08 - Added missing rear platform lights on the hood end - Center hood door height - Large rear hood intake height 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Removed seam at rear of cab (left side) 2017-11-11 - Corrected minor glitch in front truck traction pin (left side) 2017-12-17 - Revised cables/pipes under back of cab (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points |
| EMD SD70M-2 ← → | 2008-11 - 2010-03 | 2e3 | CN 8850-8914 | 2022-03-30Revision history:
2016-10-08 - Added missing rear platform lights on the hood end - Center hood door height - Large rear hood intake height - Revised intake under radiators (left side) 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) 2017-11-11 - Corrected minor glitch in front truck traction pin (left side) 2017-12-17 - Revised cables/pipes under back of cab (right side) - Revised handbrake (changed from Phase 2e2 to 2e3) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
| EMD SD70M-2 ← → | 2010-10 - 2011-02 | 2f | CN 8915-8964 | 2022-03-30Revision history:
2016-10-08 - Added missing rear platform lights on the hood end - Center hood door height - Large rear hood intake height - Revised intake under radiators (left side) 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) 2017-11-11 - Relocated hole below handbrake wheel (right side) - Corrected minor glitch in front truck traction pin (left side) 2017-12-17 - Revised cables/pipes under back of cab (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
| EMD SD75I ← → → | 1996-05 - 1996-12 | 1d2 | CN 5626-5645, 5646-5730 | 2023-01-19Revision history:
2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points 2022-12-10 - Cab sub-base door proportions (right side) 2022-12-21 - Fuel tank length 2023-01-19 - Hood door and radiator intake height | |
| EMD SD75I ← → | 1997-08 - 1999-07 | 1e | CN 5731-5800; ONT 2100-2105 | 2023-01-19Revision history:
2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points 2022-07-12 - Axle shock strut locations 2022-12-10 - Cab sub-base door proportions (right side) - Added cab side seam 2022-12-21 - Fuel tank length 2023-01-19 - Hood door and radiator intake height | |
| GE Dash 9-44CW ← → | 2004-01 - 2004-02 | 2h | CN 2200-2205 | CN Class EF-644g | 2022-11-12Revision history:
2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Corrected air reservoir length - Added missing sand hose in front underframe - Added missing brake line on truck near brake chain (left side) - Corrected brake lines 2015-07-21 - Revised vertical bars in dynamic brake intakes 2016-02-20 - Added traction pin in center of trucks 2017-01-23 - Piping behind fuel tank 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam |
| GE Dash 9-44CW ← → | 1997-02 - 1998-02 | 2b | CN 2523-2562, 2563-2602 | CN Class EF-644b, c | 2022-11-12Revision history:
2015-07-08 - Corrected air reservoir length - Added missing sand hose in front underframe - Added missing brake line on truck near brake chain (left side) - Corrected brake lines 2015-07-21 - Revised vertical bars in dynamic brake intakes 2016-02-20 - Added traction pin in center of trucks 2017-01-23 - Piping behind fuel tank 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam |
| GE Dash 9-44CW ← → | 2001-01 - 2002-09 | 2g | CN 2603-2642, 2643-2672 | CN Class EF-644d, e | 2022-11-12Revision history:
2015-07-08 - Corrected air reservoir length - Added missing sand hose in front underframe - Added missing brake line on truck near brake chain (left side) - Corrected brake lines 2015-07-21 - Revised vertical bars in dynamic brake intakes 2016-02-20 - Added traction pin in center of trucks 2017-01-23 - Piping behind fuel tank 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam |
| GE Dash 9-44CW ← → | 2004-01 - 2004-02 | 2h | CN 2673-2696 | CN Class EF-644f | 2022-11-12Revision history:
2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Corrected air reservoir length - Added missing sand hose in front underframe - Added missing brake line on truck near brake chain (left side) - Corrected brake lines 2015-07-21 - Revised vertical bars in dynamic brake intakes 2016-02-20 - Added traction pin in center of trucks 2017-01-23 - Piping behind fuel tank 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam |
| GE Dash 9-44CW ← → | 2004-06 - 2004-09 | 2h | CN (IC) 2697-2726 | CN Class EF-644h | 2022-11-12Revision history:
2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Corrected air reservoir length - Added missing sand hose in front underframe - Added missing brake line on truck near brake chain (left side) - Corrected brake lines 2015-07-21 - Revised vertical bars in dynamic brake intakes 2016-02-20 - Added traction pin in center of trucks 2016-11-06 - Revised panel under cab on conductor's side 2017-01-23 - Piping behind fuel tank 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam |
| GE Dash 9-44CWL ← → | 1994-12 | 1d | CN 2500-2522 | CN Class EF-644a | 2022-11-12Revision history:
2015-07-21 - Revised vertical bars in dynamic brake intakes 2015-09-07 - Center hood roof & side panels 2016-02-20 - Added traction pin in center of trucks 2017-01-25 - Revised cab side window size and location 2017-02-08 - Added empty handbrake chain bracket to front right truck - Corrected location of hinges on first 2 hood doors under front air intake (left side) 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts |
| GE ES44AC ← → | 2012-11 - 2012-12 | 2f1 | CN 2800-2834 | 2022-11-29Revision history:
2019-08-12 - Corrected minor transparency issue in radiators (left side) 2020-01-14 - Revised grabirons behind cab (left side) - Revised wide handrail stanchions 2020-05-24 - Moved cab mirror rearward (right side) 2021-01-12 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct - Added missing sight glass under right side radiators 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) - Narrower steps 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
| GE ES44AC ← → | 2012-12 - 2013-11 | 2f2 | CN 2835-2909 | 2022-11-29Revision history:
2019-08-12 - Corrected minor transparency issue in radiators (left side) 2020-01-14 - Revised grabirons behind cab (left side) - Revised wide handrail stanchions - Thinner side handrails 2020-05-24 - Moved cab mirror rearward (right side) 2021-01-12 - Increased corner and side handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct - Added missing sight glass under right side radiators 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) - Narrower steps 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
| GE ES44AC ← → | 2014-12 - 2019-11 | 2g | CN 2910-2999, 3800-3912 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left side) - Revised wide handrail stanchions - Thinner side handrails 2020-05-24 - Moved cab mirror rearward (right side) 2021-01-12 - Increased corner and side handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct - Added missing sight glass under right side radiators 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) - Narrower steps 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
| GE ES44DC ← → | 2006-01 - 2006-02 | 1c | CN 2220-2254 | CN Class EF-644j | 2022-11-29Revision history:
2013-12-07 - Sand brackets - Front grabirons - Traction motor cables - Left cab subbase 2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Added missing brake line on truck near brake chain (left side) - Corrected air reservoir length - Added missing sand hose in front underframe (right side) 2016-02-20 - Added traction pin in center of trucks 2016-11-06 - Revised panel under cab on conductor's side 2016-11-17 - Lowered latch on hood door below exhaust stack (right side) 2017-01-25 - Revised cab side window size and location (slightly shorter; moved slightly upward) - Added 4 holes behind left front jacking pad 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2018-03-26 - Revised door width/spacing under central air intake - Added 2 holes below front cab sub-base door 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-13 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam 2022-11-28 - Added AEI tag above left rear truck |
| GE ES44DC ← → | 2007-09 - 2007-11 | 2b | CN 2255-2289 | CN Class EF-644k, l | 2022-11-29Revision history:
2013-12-07 - Sand brackets - Front grabirons - Traction motor cables - Left cab subbase 2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Added missing brake line on truck near brake chain (left side) - Corrected air reservoir length - Added missing sand hose in front underframe (right side) 2016-02-20 - Added traction pin in center of trucks 2016-11-06 - Revised panel under cab on conductor's side 2016-11-17 - Lowered latch on hood door below exhaust stack (right side) 2017-01-25 - Revised cab side window size and location (slightly shorter; moved slightly upward) - Added 4 holes behind left front jacking pad 2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2018-03-26 - Revised door width/spacing under central air intake - Added 2 holes below front cab sub-base door 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-13 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam 2022-11-28 - Added AEI tag above left rear truck |
| GE ES44DC ← → | 2008-02 - 2008-03 | 2c | CN 2290-2309 | CN Class EF-644l | 2022-11-29Revision history:
2013-12-07 - Sand brackets - Front grabirons - Traction motor cables - Left cab subbase 2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Added missing brake line on truck near brake chain (left side) - Corrected air reservoir length - Added missing sand hose in front underframe (right side) 2016-02-20 - Added traction pin in center of trucks 2016-11-06 - Revised panel under cab on conductor's side 2016-11-17 - Lowered latch on hood door below exhaust stack (right side) 2017-01-25 - Revised cab side window size and location (slightly shorter; moved slightly upward) - Added 4 holes behind left front jacking pad 2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2018-03-26 - Revised door width/spacing under central air intake - Added 2 holes below front cab sub-base door 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-13 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam 2022-11-28 - Added AEI tag above left rear truck |
| GE ES44DC ← → | 2010 | 2e | CN 2310-2344 | CN Class EF-644m | 2022-11-29Revision history:
2013-12-07 - Sand brackets - Front grabirons - Traction motor cables - Left cab subbase 2014-02-22 - Truck casting logo and text - Short hood height 2015-07-08 - Added missing brake line on truck near brake chain (left side) - Corrected air reservoir length - Added missing sand hose in front underframe (right side) 2016-02-20 - Added traction pin in center of trucks 2016-10-09 - Corrected grills under radiator intakes 2016-11-06 - Revised panel under cab on conductor's side 2016-11-17 - Lowered latch on hood door below exhaust stack (right side) 2017-01-25 - Revised cab side window size and location (slightly shorter; moved slightly upward) - Added 4 holes behind left front jacking pad 2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-23 - Lowered cab sunshade location 2018-03-26 - Revised door width/spacing under central air intake - Added 2 holes below front cab sub-base door 2020-01-14 - Revised wide handrail stanchions 2021-01-12 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-13 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added numberboard seam 2022-11-28 - Corner step height - Added AEI tag above left rear truck |
| GE ET44AC ← → | 2015-07 - 2015-09 | CN 3000-3038 | 2022-11-28Revision history:
2021-01-12 - Increased corner and side handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) - Narrower steps 2022-11-28 - Corner step height - Center hood bolt height - Added AEI tag above left rear truck | ||
| GE ET44AC ← → | 2016 - 2020 | CN 3039-3120, 3133-3285 | 2022-11-29 | ||
| GMD GP35 ← → | 1964-08 | 1a | CN 4000-4001 | 2022-02-04Revision history:
2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2016-02-08 - Revised rear headlight housing contour 2018-11-11 - Corrected minor line glitch on latches on first engine room door 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) - Corrected corner handrail length 2021-01-04 - Changed rear pilot from rock deflector to footboards - Removed front pilot grabiron 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts | |
| GMD GP38-2(W) ← → | 1973-06 | CN 5560 re# 4760 | builder's plate: GP38-2 | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added rerail frogs - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Corrected minor line glitch on latches on cab sub-base door and first engine room door - Revised paper air filter housing 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP38-2(W) ← → | " | " | " (as modified) | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added coupler knuckle bracket (rear pilot) - Added oil retention tank (behind fuel tank) - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Corrected minor line glitch on latches on cab sub-base door and first engine room door - Revised paper air filter housing 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP38-2(W) ← → | 1973-10 - 1974-01 | CN 5561-5610 re# 4761-4810 | builder's plate: GP38-2 | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added rerail frogs - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Corrected minor line glitch on latches on cab sub-base door and first engine room door - Revised paper air filter housing 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP38-2(W) ← → | " | " | " (as modified) single plow | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added coupler knuckle bracket (rear pilot) - Added oil retention tank (behind fuel tank) - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Corrected minor line glitch on latches on cab sub-base door and first engine room door - Revised paper air filter housing 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP38-2(W) ← → | " | " | " (as modified) dual plows | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added coupler knuckle bracket (rear pilot) - Added oil retention tank (behind fuel tank) - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Corrected minor line glitch on latches on cab sub-base door and first engine room door - Revised paper air filter housing 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP40 ← → | 1966-05 - 1966-12 | CN 4002-4011 | 2022-02-04Revision history:
2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Revised exhaust stack 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points | ||
| GMD GP40 ← → | " | CN 9302-9311; ex 4002-4011 | As modified | 2022-02-04Revision history:
2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Revised exhaust stack 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points | |
| GMD GP40 ← → | 1967-10 | CN 4012-4017 | 2022-02-04Revision history:
2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Revised exhaust stack 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points | ||
| GMD GP40 ← → | " | CN 9312-9317; ex 4012-4017 | As modified | 2022-02-04Revision history:
2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised handrail stanchion spacing - Fuel tank and air reservoirs moved 1" to 1.5" rearward - Revised exhaust stack 2020-12-04 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-09 - Fuel tank height and gap from underframe 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points | |
| GMD GP40-2(W) ← → | 1976-03 - 1976-05 | CN 9633-9667 | builder's plate: GP40-2 | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added rerail frogs - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised radiator intake grills - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP40-2(W) ← → | " | " | " (as modified) | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added coupler knuckle bracket (rear pilot) - Added oil retention tank (behind fuel tank) - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised radiator intake grills - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP40-2L(W) ← → | 1974 | CN 9400-9490 | builder's plate: GP40-2L | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added rerail frogs - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised radiator intake grills - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP40-2L(W) ← ← → | 1974 - 1975 | CN 9491-9530, 9531-9632 | builder's plate: GP40-2L | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added rerail frogs - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised radiator intake grills - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP40-2L(W) ← ← → | " | CN 9400-9530, 9531-9632 | " (as modified) | 2023-01-09Revision history:
2013-01-05 - Cab handrail attachments 2014-10-19 - Added coupler knuckle bracket (rear pilot) - Added oil retention tank (behind fuel tank) - Corrected rear pilot handrail (stanchions flush on pilot) - Corrected right side handrail (angled section at cab) - Revised radiator fans (bottom rim edge and upper rim clips) 2016-02-08 - Revised rear headlight housing contour 2019-01-25 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised radiator intake grills - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-10 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD GP7 ← → | 1953-08 - 1953-11 | 2d | CN 7555-7578 re# 1700-1723, 4800-4823 | 2023-07-10Revision history:
2023-04-20 - Front flag holder location - Truck axle pedestal wear plates 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
| GMD GP9 ← → | 1955-02 - 1955-04 | 1a | CN 1724-1747 re# 4400-4423 | CN Class GR-17a | 2023-07-10Revision history:
2023-04-20 - Front flag holder location - Truck axle pedestal wear plates 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1955-04 | 1b | CN 1748-1750 re# 4424-4426 | CN Class GR-17a | 2023-07-10Revision history:
2023-04-20 - Front flag holder location - Truck axle pedestal wear plates 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1955-08 - 1956-07 | 1b | CN 2000-2024, re# 4451-4475; 4476-4495 | CN Class GR-17f | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1956-11 - 1957-12 | 2a | CN 4496-4501, re# 4200-4205; 4588:1-4609:1, re# 4206-4227; 4100-4133 | CN Class GR-17g, n, p Flexicoil trucks | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1956-11 - 1957-01 | 2a | CN 4502-4538 | CN Class GR-17h | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1957-06 - 1957-07 | 2b | CN 4560-4587 | CN Class GR-17m | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1958-02 - 1958-03 | 2b | CN 4228-4244 | CN Class GR-17q Flexicoil trucks | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1957-12 - 1958-01 | 2b | CN 4588:2-4609:2 | CN Class GR-17r | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1958-04 - 1958-05 | 3a | CN 4245-4270 | CN Class GR-17t Flexicoil trucks | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD GP9 ← → | 1959-01 - 1959-11 | 3a | CN 4271-4339, 4147-4156, 4340-4353 | CN Class GR-17u, y, z Flexicoil trucks | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
| GMD SD40 ← → | 1967-09 | CN 5000-5007 | CN Class GF-30c | 2023-04-08Revision history:
2017-10-28 - Revised brake system (Dofasco Flexicoil trucks) - Added battery charge receptacle on right side underframe behind cab - Relocated horn to recess at front of cab - Revised speed recorder cable - Added drip rail above cab side windows 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Relocated dynamic brakes - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Lower sand pipe under cab | |
| GMD SD40 ← → | 1967-10 - 1968-12 | CN 5008-5075 | CN Class GF-30d | 2023-04-08Revision history:
2017-10-28 - Revised brake system (Dofasco Flexicoil trucks) - Added battery charge receptacle on right side underframe behind cab - Relocated horn to recess at front of cab - Revised speed recorder cable - Added drip rail above cab side windows 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Lower sand pipe under cab | |
| GMD SD40 ← → | 1969-02 - 1969-03 | CN 5076-5081 | CN Class GF-30e | 2023-04-08Revision history:
2017-10-28 - Revised brake system (Dofasco Flexicoil trucks) - Added battery charge receptacle on right side underframe behind cab - Relocated horn to recess at front of cab - Revised speed recorder cable - Added drip rail above cab side windows 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Lower sand pipe under cab | |
| GMD SD40 ← → | 1969-03 - 1969-04 | CN 5082-5087 | CN Class GF-30e | 2023-04-08Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Lower sand pipe under cab | |
| GMD SD40 ← → | 1969-05 - 1971-08 | CN 5088-5110, 5132-5196 | CN Class GF-30e, h, k | 2023-04-08Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Added sand pipes running below walkway sideframe | |
| GMD SD40 ← → | 1969 | CN 5111-5131 | CN Class GF-30e, h | 2023-04-08Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Relocated dynamic brakes - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Added sand pipes running below walkway sideframe | |
| GMD SD40 ← → | 1971 | CN 5197-5214 | CN Class GF-30k | 2023-04-08Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack - Corrected error with 4th handrail stanchion from rear 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Added sand pipes running below walkway sideframe | |
| GMD SD40 ← → | 1971 | CN 5215-5240 | CN Class GF-30k, m | 2023-04-08Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-23 - Revised exhaust stack 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-11-09 - Added missing grabiron ahead of right-side battery box - Removed walkway side frame seam near step wells 2023-04-08 - Added sand pipes running below walkway sideframe | |
| GMD SD40-2(W) ← → | 1975-05 - 1975-07 | 1a1 | CN 5241-5261 | Builder's plate on all SD40-2(W) units: SD40-2 | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) - Added ditch light brackets 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | " | " | As modified | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | 1975-07 | 1a1 | CN 5262-5278 | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) - Added ditch light brackets 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | As modified | 2023-01-09Revision history:
2016-02-08 - Revised rear headlight housing contour 2017-01-21 - Revised handbrake chain with pulley (left-side view) 2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | 1976-01 | 1a2 | CN 5279-5293 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | 1978-07 - 1978-10 | 1a3 | CN 5294-5313 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD40-2(W) ← → | 1979-12 | 1b | CN 5314-5323 | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) - Corrected line glitch on rear of cab roof (left side) - Corrected lift ring glitch ahead of dynamic brake fans (right side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams | |
| GMD SD40-2(W) ← → | " | " | " | As modified | 2023-01-09Revision history:
2019-01-28 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Revised exhaust stack - Corrected minor line glitch on latches on cab sub-base door and first engine room door 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2023-01-09 - Long hood end seams |
| GMD SD50F ← → | 1985-04 - 1986-02 | CN 5400-5439, 9900-9903 | 9900-9903 initially classified as SD50AF; re# 5500-5503 & reclassified as SD60F | 2022-12-01Revision history:
2020-12-22 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Cab corners and sub-base doors - Sand hoses 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points | |
| GMD SD50F ← → | 1987-02 - 1987-07 | CN 5440-5459 | 2022-12-01Revision history:
2020-12-22 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Cab corners and sub-base doors - Sand hoses 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points | ||
| GMD SD60F ← → | 1989-02 - 1989-11 | CN 5504-5563 | 2022-12-01Revision history:
2020-12-22 - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Cab corners and sub-base doors - Sand hoses 2021-01-11 - Fuel tank height and gap from underframe 2022-12-01 - Coupler cut levers - Corner handrail end plate / stairwell attachment points | ||
| MLW FPA-4 ← → | 1958-10 - 1959-05 | CN 6760-6793 | 2022-03-01Revision history:
2022-02-18 - Increased bottom of underframe height - Relocated and revised traction motor cable brackets - Lowered side grills and upper carbody panels - Adjusted cab, window and nose proportions - Roof hatch positions 2022-03-01 - Minor side ladder changes - Carbody roof vent location (left side) - Added bolts to end diaphragm - Headlight casing and nose door | ||
| MLW FPA-4 ← → | " | VIA 6760-6793; ex-CN | As modified (includes VIA Rail-applied side grabirons) | 2022-03-01Revision history:
2022-02-18 - Increased bottom of underframe height - Relocated and revised traction motor cable brackets - Lowered side grills and upper carbody panels - Adjusted cab, window and nose proportions - Roof hatch positions 2022-03-01 - Minor side ladder changes - Carbody roof vent location (left side) - Headlight casing and nose door | |
| MLW FPB-4 ← → | 1958-10 - 1959-03 | CN 6860-6871 | 2022-03-01Revision history:
2022-02-18 - Increased bottom of underframe height - Relocated and revised traction motor cable brackets - Lowered side grills and upper carbody panels - Adjusted cab, window and nose proportions - Roof hatch positions 2022-03-01 - Minor side ladder changes - Carbody roof vent location (left side) - Added bolts to end diaphragms | ||
| MLW FPB-4 ← → | " | CN / VIA 6860-6871 | As modified | 2022-03-01Revision history:
2022-02-18 - Increased bottom of underframe height - Relocated and revised traction motor cable brackets - Lowered side grills and upper carbody panels - Adjusted cab, window and nose proportions - Roof hatch positions 2022-03-01 - Minor side ladder changes - Carbody roof vent location (left side) | |
| MLW M-420 ← → | 1973-05 - 1973-10 | CN 2500-2529 | CN class MR-20a; re# 3500-3529 | 2024-01-26Revision history:
2020-11-25 - Removed rear numberboards - Removed rear wrap-around pilot 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified Old door latches | 2024-01-26Revision history:
2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified New door latches | 2024-01-26Revision history:
2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | 1974-03 - 1974-07 | CN 2530-2559 | CN class MR-20b; re# 3530-3559 | 2024-01-26Revision history:
2020-11-25 - Removed rear wrap-around pilot 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified Old door latches | 2024-01-26Revision history:
2018-01-29 - Slight revisions to cut-off valves and fittings in air piping (right side) - Revised battery box covers (right side) - Revised handbrake wheel notch (right side) 2020-11-25 - Removed pollution collector tank behind fuel tank 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified New door latches | 2024-01-26Revision history:
2018-01-29 - Slight revisions to cut-off valves and fittings in air piping (right side) - Revised battery box covers (right side) - Revised handbrake wheel notch (right side) 2020-11-25 - Removed pollution collector tank behind fuel tank 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | 1976-09 - 1976-12 | CN 2560-2579 | CN class MR-20c; re# 3560-3579 | 2024-01-26Revision history:
2020-11-25 - Added pollution collector tank behind fuel tank 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified Old door latches | 2024-01-26Revision history:
2018-01-29 - Slight revisions to cut-off valves and fittings in air piping (right side) 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW M-420 ← → | " | " | As modified New door latches | 2024-01-26Revision history:
2018-01-29 - Slight revisions to cut-off valves and fittings in air piping (right side) 2022-03-15 - Coupler cut lever thickness and height 2024-01-26 - Corrected minor glitches in cab sunshades and class lights | |
| MLW RS-10S ← → | 1956-10 | CN 3066-3073 | CN class MR-16j; re# 3815-3822 | 2023-12-17Revision history:
2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.5" - Battery box and short hood side doors/grabirons moved rearward by 0.25" - Cab sub-base door and hinge spacing - Footboards and pilot plate - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters | |
| MLW RS-10S ← → | 1956-11 - 1957-01 | CN 3074-3093 | CN class MR-16k | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing - Reversed door handle orientation (right-side view) 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-02 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.5" - Battery box and short hood side doors/grabirons moved rearward by 0.25" - Cab sub-base door and hinge spacing - Footboards and pilot plate - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters | |
| MLW RS-18 ← → | 1956-12 - 1957-12 | 1a | CN 3615-3670 | CN class MR-18b | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | " | " | as modified | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size - Revised carbody air filters 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1957-12 - 1958-03 | 1a | CN 3671-3676 | CN class MR-18c | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | " | " | as modified | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size - Revised carbody air filters 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | 1b | CN 3677-3700 | CN class MR-18c | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | " | " | as modified | 2023-12-17Revision history:
2018-01-28 - Added winterization duct ahead of radiator fan housing 2018-12-14 - Revised piping and air fittings behind fuel tank (right-side view) - Corrected cab door handle orientation - Revised battery box covers - Added missing rear sand hatch (right-side view) - Revised short hood door size - Revised carbody air filters 2018-12-18 - Added missing pipe at rear of fuel tank 2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1958-06 | 1c | CN 3701-3704 | CN class MR-18d | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | " | " | as modified | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1958-06 - 1958-11 | 1d | CN 3705-3745 | CN class MR-18d | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | " | " | " | as modified | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1959-05 - 1959-07 | 2a | CN 3830-3839 | CN class MR-18f | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1959-06 - 1959-12 | 2b | CN 3100-3129, 3840-3849 | CN class MR-18e, f | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RS-18 ← → | 1960-01 - 1960-08 | 2c | CN 3850-3893 | CN class MR-18g | 2023-12-17Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters |
| MLW RSC-14 ← → | 1975 (R) | 2b | CN 1750-1756 | CN RS-18 rebuild (ex 3843-3849) | 2023-12-25Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters 2023-12-21 - Truck brake cylinders, brake rigging and sand lines |
| MLW RSC-14 ← → | 1975 (R) | 2c | CN 1757-1787 | CN RS-18 rebuild (ex 3850-3893 series) | 2023-12-25Revision history:
2019-01-03 - Increased frame height by 0.5" 2019-01-09 - Added radiator fan clips 2019-01-12 - Added rooftop vent on conductor's side behind cab 2021-12-30 - All long hood components moved rearward (radiator fan by 1.75", radiator intakes by 1", hood doors and center hood section by 0.75") - Hood roof panels, hinges and exhaust housing - Cab lengthened by 0.5" and moved rearward by 0.25" - Cab sub-base door and hinge spacing - Removed extra bolt around radiator intakes 2022-03-23 - Coupler cut lever and pilot end handrail 2023-12-17 - Corrected number of radiator shutters 2023-12-21 - Truck brake cylinders, brake rigging and sand lines |
1:36 Drawings
| Model | Built | Phase | Numbers | Notes |
|---|---|---|---|---|
| EMD F3A ← → | 1948-05 | 2b | CN 9000, 9002, 9003, 9005 | |
| EMD F3B ← → | 1948-05 | 2b/3 | CN 9001, 9004 | |
| EMD F7Au ← → | CN 9171 | F3A rebuild | ||
| EMD SD70I ← → | 1995-07 - 1995-11 | 1d2 | CN 5600-5625 | |
| EMD SD70M-2 ← → | 2005-12 - 2006-04 | 2a1 | CN 8000-8024 | |
| EMD SD70M-2 ← → | " | " | " | as modified |
| EMD SD70M-2 ← → | 2007-07 - 2007-11 | 2e1 | CN 8800-8849 | |
| EMD SD70M-2 ← → | 2008-11 - 2010-03 | 2e2 | CN 8850-8914 | |
| EMD SD70M-2 ← → | 2010-09 - 2011-02 | 2f | CN 8915-8964 | |
| EMD SD70M-2 ← → | " | " | " | as modified |
| EMD SD75I ← → → | 1996-05 - 1996-12 | 1d2 | CN 5626-5645, 5646-5730 | |
| EMD SD75I ← → | 1997-08 - 1999-07 | 1e | CN 5731-5800, ONT 2100-2105 | |
| GE Dash 8-40CM ← → | 1990-03 - 1990-03 | CN 2400-2429 | ||
| GE Dash 8-40CM ← → | 1992-11 - 1992-12 | CN 2430-2454 | ||
| GE Dash 9-44CW ← → | 2004 | 2h | CN 2200-2205 | CN Class EF-644g |
| GE Dash 9-44CW ← → | 1997 - 1998 | 2b | CN 2523-2562, 2563-2602 | CN Class EF-644b, c |
| GE Dash 9-44CW ← → | 2000 - 2002 | 2g | CN 2603-2642, 2643-2672 | CN Class EF-644d, e |
| GE Dash 9-44CW ← → | 2004 | 2h | CN 2673-2696 | CN Class EF-644f |
| GE Dash 9-44CW ← → | 2004 | 2h | CN (IC) 2697-2726 | CN Class EF-644h |
| GE ES44DC ← → | 2007 | 2b | CN 2255-2289 | CN Class EF-644k, l |
| GE ES44DC ← → | 2008-03 | 2c | CN 2290-2309 | CN Class EF-644l |
| GMD F7A ← → | 1951-04 - 1951-08 | 1b3 | CN 9028-9054 even | |
| GMD F7A ← → | 1951 - 1952 | 1b3 | CN 9056-9086 even | |
| GMD F7A ← → | 1952 | 2a | CN 9088-9142 even | |
| GMD F7A ← → | " | 2b | " | |
| GMD F7Au ← → | CN 9150-9157, 9159-9165, 9167-9170, 9172-9179 | F7A rebuild | ||
| GMD F7Au ← → | " | F7A rebuild | ||
| GMD F7Bu ← → | CN 9190-9199 | F7B rebuild | ||
| GMD GP38-2 ← → | 1972-11 - 1973-06 | 1b | CN 5500-5559 | |
| GMD GP38-2(W) ← → | 1973-06 | CN 5560; re# 4760 | builder's plate: GP38-2 | |
| GMD GP38-2(W) ← → | " | CN 4760 | " (as modified) | |
| GMD GP38-2(W) ← → | 1973-10 - 1974-01 | CN 5561-5610; re# 4761-4810 | builder's plate: GP38-2 | |
| GMD GP38-2(W) ← → | " | CN 4761-4810 | " (as modified) single plow | |
| GMD GP38-2(W) ← → | " | " | " (as modified) dual plows | |
| GMD GP40 ← → | 1966-05 - 1966-12 | CN 4002-4011 | ||
| GMD GP40 ← → | " | CN 9302-9311; ex 4002-4011 | As modified | |
| GMD GP40 ← → | 1967-10 | CN 4012-4017 | ||
| GMD GP40 ← → | " | CN 9312-9317; ex 4012-4017 | As modified | |
| GMD GP40-2(W) ← → | 1976-03 - 1976-05 | CN 9633-9667 | Builder's plate: GP40-2 | |
| GMD GP40-2(W) ← → | " | " | " (as modified) | |
| GMD GP40-2L(W) ← ← → | 1974-03 - 1975-09 | CN 9400-9530, 9531-9632 | builder's plate: GP40-2L | |
| GMD GP40-2L(W) ← ← → | " | " | " (as modified) | |
| GMD GP9 ← → | 1955-02 - 1955-04 | 1a | CN 1724-1747 re# 4400-4423 | CN Class GR-17a |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 ← → | 1955-04 | 1b | CN 1748-1750 re# 4424-4426 | CN Class GR-17a |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 ← → | 1955-08 - 1957-01 | 2a | CN 4451-4495, 4502-4538 | CN Class GR-17f, h |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 ← → | 1956-11 | 2a | CN 4496-4501 re# 4200-4205 | CN Class GR-17g |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 ← → | 1957-07 - 1958-03 | 2a | CN 4100-4133; 4228-4244; 4588:1-4609:1, re# 4206-4227 | CN Class GR-17n, p, q Flexicoil trucks |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 ← → | 1957-06 - 1958-01 | 2b | CN 4560-4587, 4588:2-4601:2 | CN Class GR-17m, r |
| GMD GP9 ← → | " | " | " | " As modified |
| GMD GP9 slug ← → | 1986 - 1988 | CN 211-241 | CN GP9 rebuild | |
| GMD GP9 slug ← → | 1990 | CN 242-263 | CN GP9 rebuild | |
| GMD GP9RM ← → | 1981 - 1984 (R) | 1b | CN 4000-4036, 4100-4116 | Spark arrestors |
| GMD GP9RM ← → | " | 2 | " | Spark arrestors |
| GMD GP9RM ← → | " | 3 | " | Spark arrestors |
| GMD GP9RM ← → | 1985 (R) | 1b | CN 7000-7013 | |
| GMD GP9RM ← → | " | " | " | Spark arrestors |
| GMD GP9RM ← → | " | 2 | " | |
| GMD GP9RM ← → | " | " | " | Spark arrestors |
| GMD GP9RM ← → | 1989 - 1990 (R) | 1a | CN 4117-4128 | |
| GMD GP9RM ← → | " | 2 | " | |
| GMD GP9RM ← → | " | 3 | " | |
| GMD GP9RM ← → | 1991 - 1993 (R) | 1b | CN 4129-4143, 7014-7083 | |
| GMD GP9RM ← → | " | 2 | " | |
| GMD GP9RM ← → | " | 3 | " | |
| GMD SD40-2(W) ← → | 1975-05 - 1975-07 | 1a1 | CN 5241-5261 | Builder's plate on all SD40-2(W) units: SD40-2 |
| GMD SD40-2(W) ← → | 1975-07 | 1a1 | CN 5262-5278 | |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| GMD SD40-2(W) ← → | 1976-01 | 1a2 | CN 5279-5293 | |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| GMD SD40-2(W) ← → | 1978-07 - 1978-10 | 1a3 | CN 5294-5313 | |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| GMD SD40-2(W) ← → | 1979-12 | 1b | CN 5314-5323 | |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| GMD SD40-2(W) ← → | 1980-04 - 1980-05 | 1b | CN 5324-5353 | |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| GMD SD40-2(W) ← → | " | " | " | As modified |
| MLW M-420 ← → | 1973-05 - 1973-10 | CN 2500-2529 | re# 3500-3529 | |
| MLW M-420 ← → | " | " | As modified Old door latches | |
| MLW M-420 ← → | " | " | As modified New door latches | |
| MLW M-420 ← → → | 1974-03 - 1976-12 | CN 2530-2559, 2560-2579 | re# 3530-3559, 3560-3579 | |
| MLW M-420 ← → → | " | " | As modified Old door latches | |
| MLW M-420 ← → → | " | " | As modified New door latches |
1:55 Drawings
| Model | Phase | Numbers | Notes | Accuracy |
|---|---|---|---|---|
| CLC CFA16-4 ← → | CN 8700-8704 even | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| CLC CFA16-4 ← → | CN 8706-8744 even | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| CLC CPA16-5 ← → | CN 6700-6705 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| CLC H16-44 ← → | 3b | CN 1841-1858 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD F3Au ← | CN F3A rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| EMD SD70I ← → | 1d2 | CN 5600-5625 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD70M-2 ← → | 2a1 | CN 8000-8024 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD75I ← → | 1d2 | CN 5626-5730 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| EMD SD75I ← → | 1e | CN 5731-5800; ONT 2100-2105 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GE Dash 8-40CM ← → | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GE Dash 9-44CW ← ← → | 2b, 2g | CN 2523-2602, 2603-2672 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GE Dash 9-44CW ← → | 2h | CN 2673-2696, IC 2697-2726 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GE Dash 9-44CWL ← → | CN 2500-2522 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GE ES44DC ← → | CN 2220-2254 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD F7Au ← → | 1 | CN Phase 1 F7A rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD F7Au ← → | 2 | CN Phase 2 F7A rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP35 ← → | 1a | CN 4000-4001 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP38-2 ← → | 1b | CN 5500-5559 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP38-2(W) ← → | CN 5560-5610 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP38-2(W) ← → | CN 4760-4810; ex-5560-5610 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP40 ← → | CN 4013-4017 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP40 ← → | CN 4002-4012 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP40-2(W) ← → | CN 9633-9667 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP40-2(W) ← → | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2(W) ← → | HCRY 3010 | ex-CN 9640 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2(W) ← → | HCRY 3012 | ex-CN 9649 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2(W) ← → | HCRY 3013 | ex-CN 9646 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2(W) ← → | MEC 509-519 | ex-CN | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2(W) ← → | RMRX 8014-8015 | ex-CN | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← ← → | CN 9400-9530, 9531-9632 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD GP40-2L(W) ← ← → | " | as modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← → | HCRY 3011 | ex-CN 9403 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← ← → | KCS 4700-4707 | ex-CN | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← → | KCS 4708 | ex-CN | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← ← → | KCS 4709-4722 | ex-CN | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← → | MEC 500-507 | ex-CN | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP40-2L(W) ← → | MEC 508 | ex-CN | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 2b | CN 4000-4036, 4110-4116 | Spark arrestors | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD GP9RM ← → | 3 | " | Spark arrestors | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD GP9RM ← → | 2a | CN 7000-7013 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | " | " | Spark arrestors | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD GP9RM ← → | 1 | CN 4117-4128 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 2b | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 3 | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 1 | CN 4129-4143, 7014-7083 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 2b | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 3 | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 2b | CN 7200-7231 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | " | " | Spark arrestors | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD GP9RM ← → | 2b | CN 7232-7248 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | " | " | Spark arrestors | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD GP9RM ← → | 2b | CN 7249-7270 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 3 | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 2b | CN 7271-7280 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD GP9RM ← → | 3 | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40 ← → | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD SD40 ← → | CN version | No dynamic brakes | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | 1a1 | CN 5241-5261 | Builder's plate on all SD40-2(W) units: SD40-2 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | 1a2 | CN 5279-5293 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | 1a3 | CN 5294-5313 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | 1b | CN 5314-5323 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | 1b | CN 5324-5353 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40-2(W) ← → | 2 | CN 5354-5363 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| GMD SD40-2(W) ← → | " | " | As modified | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
| GMD SD40u ← → | CN SD40 rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD SD50F ← | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |||
| GMD SD60F ← | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |||
| GMD SW1200RM ← | CN Rebuild | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD SW1200RS ← → | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| GMD SW1200RS ← → | CN version Spark arrestors | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| MLW C-630M ← | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| MLW C-630M ← | " | As modified | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW FPA-2 ← → | CN 6758-6759; ex-CN 6755, 6751 | As modified | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW FPA-4 ← → | CN 6760-6793 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| MLW FPA-4 ← → | As modified | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| MLW M-420 ← → | CN 2500-2530 | re# 3500-3529 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-420 ← → | " | As modified Old door latches | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-420 ← → | " | As modified New door latches | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-420 ← → → | CN 2530-2559, 2560-2579 | re# 3530-3559, 3560-3579 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-420 ← → → | " | As modified Old door latches | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-420 ← → → | " | As modified New door latches | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW M-636 ← | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
| MLW RS-10 ← → | CN version | Dynamic brakes lightweight trucks | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW RS-10 ← → | CN version | No dynamic brakes | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW RS-10 ← → | CN version | No dynamic brakes lightweight trucks | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW RS-10 ← → | CN version | Dynamic brakes | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW RS-18M ← | CN version | CN rebuild HEP generator | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
| MLW S-13 ← | CN version | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: