Undecorated Drawings - CNW
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
ALCO C-425 ← → | 1966-12 | 2c | CNW 401-404 | re# 4255-4258 | 2024-01-03 |
EMD GP15-1 ← → | 1976-06 - 1976-07 | CNW 4400-4424 | 2022-03-02Revision history:
2019-07-30 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Middle hood doors narrowed by 0.75" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Corrected handrail glitch behind cab (left-side view) 2020-12-09 - Revised side handrail stanchions - Increased handrail thickness - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points 2022-03-02 - Horn manifold and back cap dimensions | ||
EMD GP18 ← → | 1960-03 | 1 | CNW 1774-1779 | 2023-07-10Revision history:
2020-12-05 - Increased handrail thickness 2022-01-03 - Larger roof lift rings - Added lift rings on short hood - Removed grabiron behind rear fan - Exhaust stacks 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Corner step height increased by 2" - Footboard height increased by 1.25" - Revised coupler carrier / draft gear 2023-02-07 - Removed handrail stanchion top clamps 2023-02-16 - Fuel tank height - Fuel filler 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP30 ← → | 1963-04 | 1e | CNW 810-823 | 2022-03-15Revision history:
2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2019-08-13 - Removed dynamic brakes (left side) 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1964-02 | 1a1 | CNW 824-825 | No dynamic brakes | 2022-03-21Revision history:
2018-11-11 - Corrected minor line glitch on latches on first engine room door 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions |
EMD GP35 ← → | 1964-03 - 1964-04 | 1a2 | CNW 826-833 | No dynamic brakes | 2022-03-21Revision history:
2018-11-11 - Corrected minor line glitch on latches on first engine room door 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) - Removed dynamic brakes (left-side view) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions |
EMD GP35 ← → | 1964-04 | 1a2 | CNW 834-843 | No dynamic brakes | 2022-03-21Revision history:
2018-11-11 - Corrected minor line glitch on latches on first engine room door 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions |
EMD GP38-2 ← → | 1979-11 - 1979-12 | 2b2 | CNW 4600-4634 | ordered by RI | 2023-10-25Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised paper air filter housing and dynamic brake taper - Revised roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward 2020-12-08 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (right rear under walkway) 2021-01-09 - Air pipe vent valve (left front under walkway) - Fuel tank height and gap from underframe 2022-02-08 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2023-01-09 - Long hood end seams 2023-10-25 - Nathan P-series horn dimensions |
EMD GP50 ← → | 1980-05 - 1980-09 | 1a1 | CNW 5050-5099 | 2022-11-30Revision history:
2013-01-25 - Central air intake, dynamic brake housing (right side) 2013-03-05 - Corner handrails, pilot braces, rear end plate - Traction motor cables 2014-02-17 - Truck shape and casting logo 2014-10-23 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2015-08-19 - Air reservoir piping (left side) 2019-08-06 - Revised center hood door spacing - Revised hood behind cab - Blower duct widened by 1" (Phase 1 versions) - Increased height of walkway blower duct and bottom of hood doors - Corrected minor line glitch on latches on first engine room door 2020-12-11 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-11 - Fuel tank height and gap from underframe 2022-11-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions | |
EMD SD38-2 ← → | 1975-01 | 1b1 | CNW 6650-6659 | 2023-01-09Revision history:
2016-04-29 - Added truck details behind steps 2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-23 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised roof fan hatch - Revised paper air filter housing 2020-12-20 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-20 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → → | 1973-08 - 1974-04 | 1a2 | CNW 6801-6815, 6816-6865 | 2023-01-09Revision history:
2012-12-17 - Air reservoir size 2013-03-24 - End plates 2014-02-17 - Truck shape and casting logos 2014-10-22 - Radiator and dynamic brake fans (bottom rim edge and upper rim clips) 2014-11-07 - Inertial air intakes (added ridge on top) - Revised center axle shock strut 2016-04-14 - Revised steps 2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Corrected minor line glitch on latches on first engine room door - Revised exhaust stack 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2022-11-08 - Removed rear footboards (left side) 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1974-09 | 1a2 | CNW 6866-6890 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Corrected minor line glitch on latches on first engine room door - Revised exhaust stack 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2022-11-08 - Removed rear footboards (left side) 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1975-01 - 1975-02 | 1b1 | CNW 6891-6925 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Corrected minor line glitch on latches on first engine room door - Revised exhaust stack 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD40-2 ← → | 1976-11 | 1c2 | CNW 6926-6935 | 2023-01-09Revision history:
2019-01-22 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch - Corrected minor line glitch on latches on first engine room door - Revised exhaust stack 2020-12-18 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Air pipe vent valve (left front / right rear under walkway) - Sand lines (larger pipe diameter, revised hoses) - Adjusted height of center hinge of engine room doors - Added missing line segment in traction motor cables above fuel filler (left side) 2021-01-09 - Fuel tank height and gap from underframe 2022-03-19 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD45 ← → | 1967-02 - 1967-03 | 1b1 | CNW 901-920 | 2022-03-21Revision history:
2014-12-31 - Underframe height - Truck details and casting logos 2017-03-18 - Narrower cab sub-base ribs 2017-05-20 - Revised handrail stanchion at rear of walkway blower duct 2017-10-08 - Corrected minor line glitch on latches on first engine room door - Revised bottom flange of dynamic brake and radiator fans 2017-11-11 - Revised central hood door spacing 2019-01-17 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Middle section of hood moved rearward by 1" - Rear section of hood shortened by 1" - Increased height of walkway blower duct and bottom of hood doors 2019-01-28 - Shifted rear 4 engine compartment doors, rear hood doors, radiators and dynamic brakes 0.5" forward 2019-08-10 - Added missing grabiron ahead of right-side battery box 2020-11-07 - Added antenna 2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions | |
EMD SD45 ← → | 1969-01 - 1969-02 | 2b1 | CNW 937-977 | 2022-12-05Revision history:
2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions | |
EMD SD50 ← → | 1985-11 - 1985-12 | 2c | CNW 7000-7034 | 2024-01-30 | |
EMD SD60 ← → | 1986-08 - 1986-10 | CNW 8001-8055 | 2023-01-19Revision history:
2017-07-01 - Removed angled braces under front walkway extension - Corrected latches on first and last tall hood doors 2017-12-31 - Revised angled sheet behind bottom step - Revised piping behind fuel tank 2020-01-05 - Revised center hood door spacing - Increased height of walkway blower duct and bottom of hood doors - Revised hood behind cab (right-side view) 2020-11-28 - Shifted first hood door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-26 - Corrected location of handrail attachment point to rear of cab (left side) 2021-01-10 - Fuel tank height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate / stairwell attachment points 2023-01-19 - Hood door and radiator intake height | ||
GE AC4400CW ← → | 1994-11 - 1994-12 | 1a2 | CNW 8801-8835 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers and brackets - Revised front traction motor cable bracket (behind where front yaw damper was located) - Corrected underframe line behind front fuel filler (right side) - Removed electronic fuel gauge and relocated fuel cut-off switch - Added light under cab - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side view) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE Dash 8-40C ← → | 1989-06 - 1989-08 | 1b | CNW 8501-8530 | Vertical short hood grabirons added shortly after delivery | 2022-11-18Revision history:
2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts |
GE Dash 8-40C ← → | 1990-08 - 1991-09 | 2b | CNW 8531-8577 | 2022-11-18Revision history:
2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE Dash 9-44CW ← → | 1993-11 - 1994-01 | 1a | CNW 8601-8665 | Early Hi-Ad trucks | 2022-11-12Revision history:
2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2017-09-30 - Removed incorrect line under bell 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-11-12 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts |
GE Dash 9-44CW ← → | 1994-04 - 1994-05 | 1b | CNW 8666-8730 | 2022-11-12Revision history:
2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2017-09-30 - Removed incorrect line under bell 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-11-12 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts |
1:36 Drawings
Model | Built | Phase | Numbers | Notes |
---|---|---|---|---|
ALCO C-425 ← → | 1966-12 | 2 | CNW 401-404 | |
EMD SD38-2 ← → | 1975-01 | 1a | CNW 6650-6659 | |
EMD SD40-2 ← → → | 1973-08 - 1974-04 | 1a2 | CNW 6801-6865 | |
EMD SD40-2 ← → | 1974-09 | 1a2 | CNW 6866-6890 | |
EMD SD40-2 ← → | 1975-01 - 1975-02 | 1b1 | CNW 6891-6925 | |
EMD SD40-2 ← → | 1976-11 | 1c2 | CNW 6926-6935 | |
EMD SD60 ← → | 1986-08 - 1986-10 | CNW 8001-8055 |
1:55 Drawings
Model | Phase | Numbers | Notes | Accuracy |
---|---|---|---|---|
EMD GP15-1 ← → | CNW 4400-4424 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP30 ← → | 1e | CNW 810-823 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1a2 | CNW 826-843 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1c | CNW 844-865 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP38-2 ← → | 2a | CNW 4600-4634 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP50 ← → | 1a1 | CNW 5050-5099 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD38-2 ← → | 1b | CNW 6650-6659 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40 ← → | 1a1, 1a3 | CNW 867-892 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | 1c1 | CNW 6926-6935 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | 1a2, 1b1 | CNW 6801-6925 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD45 ← → | 1b1 | CNW 901-920 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD45 ← → | 2b1 | CNW 937-977 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD60 ← → | CNW 8001-8055 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE AC4400CW ← → | 1a | CNW 8801-8835 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE Dash 8-40C ← → | CNW 8501-8577 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE Dash 9-44CW ← → | 1a, 1b | CNW 8601-8730 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE U30C ← → | 2a | CNW 930-936 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: