Undecorated Drawings - RDG
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
ALCO C-430 ← → | 1966-07 | RDG 5211-5212 | 2022-03-04Revision history:
2017-10-07 - Revised dimensions of dynamic brake hatch 2017-12-31 - Added hinged panels on long hood end 2021-12-30 - Hood roof panels and hinges 2022-03-04 - Redrawn cab face (revised dimensions and nose/roof contours) - Cab sides moved rearward by 0.5" - Front/rear hood ends moved inward by 0.25" - Hood length reduced by 0.75" (length removed in 4 doors under exhaust stack) - Coupler cut lever thickness and height - Horn manifold and back cap dimensions | ||
EMD GP30 ← → | 1962-03 - 1962-07 | 1a | RDG 5501-5520 | 2022-03-15Revision history:
2014-10-24 - Radiator fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2015-01-20 - Revised radiator intakes - distinction between Phases 1a-1c2 vs. 1d-2b 2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1963-12 | 1a1 | RDG 6501-6506 | re# 3620-3625 | 2022-03-02Revision history:
2018-11-11 - Corrected minor line glitch on latches on first engine room door 2018-11-15 - Corrected glitch in speed recorder cable 2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions |
EMD GP35 ← → | 1964-08 - 1964-09 | 1b1 | RDG 3626-3655 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP35 ← → | 1965-05 | 1d | RDG 3656 | 2022-03-02Revision history:
2019-01-18 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood 2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP40-2 ← → | 1973-12 | 1a2 | RDG 3671-3675 | 2023-01-09Revision history:
2017-09-27 - Corrected minor line glitch on latches on first engine room door 2019-01-21 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Revised hood section under inertial air intake - Gap from seam to middle hood doors shortened by 0.75" - Middle hood doors shortened by 0.25" - Increased height of walkway blower duct and bottom of hood doors - Corrected seam at bottom corners of long hood - Revised radiator intake grills and roof fan hatch 2019-01-24 - Front left traction motor cables moved 2.25" rearward - Front right traction motor cables and air piping moved 0.75" to 1" rearward - Revised exhaust stack 2020-12-07 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) - Increased metal sand pipe diameter - Air pipe vent valve (left front / right rear under walkway) 2021-01-09 - Fuel tank height and gap from underframe 2022-02-07 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Revised ribs on blower duct 2022-03-03 - Horn manifold and back cap dimensions 2023-01-09 - Long hood end seams | |
EMD SD45 ← → | 1967-07 | 2a1 | RDG 7600-7604 | 2022-03-29Revision history:
2020-12-21 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator and dynamic brake fan dimensions and spacing - Fuel tank vent pipe (increased diameter, revised fittings) 2021-01-10 - Fuel tank height and gap from underframe 2022-03-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions | |
EMD SW1001 ← → | 1973-10 - 1973-11 | RDG 2601-2625 | 2020-12-22Revision history:
2020-12-22 - Increased handrail thickness |
1:36 Drawings
Model | Built | Phase | Numbers | Notes |
---|---|---|---|---|
EMD GP39-2 ← → | 1974-11 - 1974-12 | 1 | RDG 3401-3420 | |
EMD GP40-2 ← → | 1973-12 | 1a2 | RDG 3671-3675 | |
EMD SD45 ← → | 1967-07 - 1967-08 | 2a1 | RDG 7600-7604 |
1:55 Drawings
Model | Phase | Numbers | Notes | Accuracy |
---|---|---|---|---|
ALCO C-424 ← → | 1 | RDG 5201-5210 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
ALCO C-630 ← → | RDG 5300-5306 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
ALCO C-630 ← → | RDG 5307-5311 | Hi-ad trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP30 ← → | 1a | RDG 5501-5520 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1a1 | RDG 3620-3625 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP35 ← → | 1b1 | RDG 3626-3655 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
FM H24-66 ← → | 1b | RDG 800-806 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
FM H24-66 ← → | 1b | RDG 860-861 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
FM H24-66 ← → | 2 | RDG 807-808 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
FM H24-66 ← → | 2 | RDG 862-867 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: