Undecorated Drawings - UP
Selected scales: |
1:18 Drawings
Model | Built | Phase | Numbers | Notes | Last modified |
---|---|---|---|---|---|
EMD GP20 ← → | 1960-07 - 1960-08 | 1a | UP 700-729 | re# 470-499 | 2023-07-10Revision history:
2020-12-05 - Increased handrail thickness - Revised radiator and dynamic brake fans 2022-01-03 - Larger roof lift rings - Added lift rings around dynamic brakes 2022-03-21 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Corner step height increased by 2" - Footboard height increased by 1.25" - Revised coupler carrier / draft gear - Horn manifold and back cap dimensions 2023-02-04 - Corrected line glitch in MU connector housing 2023-02-07 - Removed handrail stanchion top clamps - Adjusted handrail stanchion spacing next to short hood 2023-02-16 - Fuel tank height - Added missing line segment on bottom front edge of generator room doors (right side) 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
EMD GP30 ← → | 1962-07 - 1962-10 | 1b2 | UP 800-875 | 2022-03-15Revision history:
2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP30 ← → | 1963-02 - 1963-03 | 1d | UP 700-734 | 2022-03-15Revision history:
2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP30 ← → | 1963-06 | 2a | UP 735 | 2022-03-15Revision history:
2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2016-02-27 - Corrected pilots, support plates and footboards (representing GP18-GP30 version rather than GP35 and later version) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2017-10-07 - Revised bottom hatches on hood ends - Removed bottom hatch latch hooks on short hood 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) 2022-03-15 - Horn manifold and back cap dimensions | |
EMD GP30B ← → | 1963-04 - 1963-06 | 1e | UP 700B-726B | 2022-02-04Revision history:
2014-10-24 - Radiator fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2015-01-20 - Revised radiator intakes - distinction between Phases 1a-1c2 vs. 1d-2b 2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) | |
EMD GP30B ← → | " | 2a | " | 2022-02-04Revision history:
2014-10-24 - Radiator fans (bottom rim edge and upper rim clips) - Truck shape and casting logos 2015-01-20 - Revised radiator intakes - distinction between Phases 1a-1c2 vs. 1d-2b 2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) | |
EMD GP30B ← → | 1963-06 - 1963-07 | 2a | UP 727B-739B | Steam generator | 2022-02-04Revision history:
2015-07-26 - Removed angled walkway plate from top step - Revised engine room door height (0.5" lower) - Corrected broken line in cab roof (right-side view) - Added access hatch near dynamic brake intake (left-side view) 2017-09-02 - Corrected minor line glitch on latches on first engine room door - Revised coupler pockets - Corrected mismatched hood seams behind conductor's side inertial air intake - Revised center radiator fan (changed to cap-top instead of open-top) 2019-07-31 - Relocated front hood seam resulting in revised hood proportions - Front section of hood lengthened and blower duct widened by 1" - Gap from seam to middle hood doors narrowed by 0.75" - Middle hood doors narrowed by 0.25" - Increased height of walkway blower duct and bottom of hood doors 2020-12-06 - Increased handrail thickness - Revised radiator fans (48" fans) 2022-01-30 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts - Corrected minor transparency glitch with front truck traction motor air ducts (right side) |
EMD GP35 ← → | 1964-05 - 1964-07 | 1b1 | UP 740-761 | 2022-03-02Revision history:
2020-12-06 - Increased handrail thickness - Revised radiator and dynamic brake fans (48" fans) 2022-01-29 - Coupler cut lever and pilot details - Corner handrail end plate / stairwell attachment points - Dynamic brake housing dimensions and shape - Added missing portion of #2 (left side) and #3 (right side) traction motor air ducts 2022-03-02 - Horn manifold and back cap dimensions | |
EMD GP40X ← → | 1977-12 - 1978-03 | UP 9000-9005 | 2023-01-02 | ||
EMD GP40X ← → | " | " | As modified (early 1980s) | 2023-01-02 | |
EMD GP9 ← → | 1954-01 | 1a | UP 205-244 | 2023-07-10Revision history:
2023-04-08 - Air reservoir piping (left side) 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9 ← → | 1954-02 - 1954-04 | 1a | UP 130-204 | 2023-07-10Revision history:
2023-04-08 - Air reservoir piping (left side) 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9 ← → | 1954-04 - 1954-06 | 1a | UP 245-248 | 2023-07-10Revision history:
2023-04-08 - Air reservoir piping (left side) 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9 ← → | 1954-08 - 1954-09 | 1b | UP 250-294 | 2023-07-10Revision history:
2023-04-08 - Air reservoir piping (left side) 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9 ← → | 1957-07 - 1957-10 | 3c | UP 300-349 | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9 ← → | 1959-03 - 1959-04 (r/b) | 3c | UP 301, 305 | GP9 rebuild turbocharger added by EMD GP20 prototype | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
EMD GP9B ← → | 1954-02 - 1954-04 | 1a | UP 130B-204B | 2023-07-10Revision history:
2023-04-08 - Air reservoir piping (left side) 2023-04-24 - Step kick plate height 2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9B ← → | 1957-09 - 1957-10 | 3c | UP 300B-349B | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) | |
EMD GP9B ← → | 1959-05 (r/b) | 3c | UP 308B | GP9 rebuild turbocharger added by EMD GP20 prototype | 2023-07-10Revision history:
2023-07-10 - Moved latches under radiators from 2nd to 3rd door from long hood end (right side) |
EMD SD24 ← → | 1959-07 - 1959-09 | UP 400-429 | 2023-11-09 | ||
EMD SD24B ← → | 1959-07 - 1959-09 | UP 400B-444B | 2023-11-08 | ||
EMD SD60 ← → | 1986-02 - 1986-05 | UP 6000-6059 | 2023-01-19Revision history:
2020-01-05 - Revised center hood door spacing - Increased height of walkway blower duct and bottom of hood doors - Revised hood behind cab (right-side view) 2020-11-28 - Shifted first hood door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-26 - Corrected location of handrail attachment point to rear of cab (left side) 2021-01-10 - Fuel tank length, height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions 2023-01-19 - Hood door and radiator intake height | ||
EMD SD60 ← → | 1988-02 - 1988-06 | UP 6060-6084 | 2023-01-19Revision history:
2020-01-05 - Revised center hood door spacing - Increased height of walkway blower duct and bottom of hood doors - Revised hood behind cab (right-side view) 2020-11-28 - Shifted first hood door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised radiator fan dimensions and spacing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-26 - Corrected location of handrail attachment point to rear of cab (left side) 2021-01-10 - Fuel tank length, height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate / stairwell attachment points - Horn manifold and back cap dimensions 2023-01-19 - Hood door and radiator intake height | ||
EMD SD60M ← → | 1990-09 - 1990-12 | 1d | UP 6216-6268 | 2023-01-19Revision history:
2020-11-28 - Revised cab / short hood proportions (moved front edge forward by 0.75"; increased total cab length by 1.5") - Shifted first engine room door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" - Revised rooftop access panels over engine compartment 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised anticlimber supports - Revised radiator fan dimensions and spacing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-08 - Removed rear numberboards 2021-01-10 - Fuel tank length, height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate attachment points - Horn manifold and back cap dimensions 2023-01-19 - Hood door and radiator intake height - Reversed orientation of radiator intakes (left side) | |
EMD SD60M ← → | 1991-11 - 1992-03 | 2b | UP 6269-6315 | 2023-01-19Revision history:
2020-11-28 - Revised cab / short hood proportions (moved front edge forward by 0.75"; increased total cab length by 1.5") - Shifted first engine room door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised anticlimber supports - Revised radiator fan dimensions and spacing - Revised headlight housing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-08 - Removed rear numberboards 2021-01-10 - Fuel tank length, height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate attachment points - Horn manifold and back cap dimensions 2023-01-19 - Hood door and radiator intake height - Reversed orientation of radiator intakes (left side) | |
EMD SD60M ← → | 1992-10 | 2b | UP 6316-6365 | 2023-01-19Revision history:
2020-11-28 - Revised cab / short hood proportions (moved front edge forward by 0.75"; increased total cab length by 1.5") - Shifted first engine room door, inertial air intake, dynamic brakes and blower duct rearward by 0.25" to 0.5" 2020-12-03 - Revised side handrail stanchions - Increased handrail thickness - Revised anticlimber supports - Revised radiator fan dimensions and spacing - Revised headlight housing 2020-12-05 - Increased fuel tank vent pipe diameter - Sand lines (larger pipe diameter, revised hoses) 2020-12-08 - Removed rear numberboards 2021-01-10 - Fuel tank length, height and gap from underframe 2022-12-12 - Coupler cut levers - Corner handrail end plate attachment points - Horn manifold and back cap dimensions 2023-01-19 - Hood door and radiator intake height - Reversed orientation of radiator intakes (left side) | |
EMD SD70ACe ← → | 2005-01 - 2005-07 | 2a2 | UP 8309-8423, 1982, 1983, 1988, 4141 | 2022-03-30Revision history:
2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Removed seam at rear of cab (left side) - Revised inverter cabinet grills 2017-12-17 - Removed angled brace behind end plates 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
EMD SD70ACe ← → | 2006-05 - 2006-08 | 2c | UP 8424-8520, 1989, 1995, 1996 | 2022-03-30Revision history:
2017-02-06 - Relocated traction motor cables above rear truck (left side) - Minor revisions to cables above front truck (left side) - Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side) - First hood door on left side changed from bolted to hinged - Revised truck casting text and air dryer location 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Removed seam at rear of cab (left side) - Revised inverter cabinet grills 2017-12-17 - Removed angled brace behind end plates 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
EMD SD70ACe ← → | 2007-02 - 2007-07 | 2d1 | UP 8521-8620 | 2022-03-30Revision history:
2017-02-06 - Relocated traction motor cables above rear truck (left side) - Minor revisions to cables above front truck (left side) - Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side) - First hood door on left side changed from bolted to hinged 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Removed seam at rear of cab (left side) - Revised inverter cabinet grills 2017-12-17 - Removed angled brace behind end plates - Revised cables/pipes under back of cab (right side) 2018-03-28 - Revised piping ahead of air reservoirs (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
EMD SD70ACe ← → | 2008-05 - 2008-08 | 2e2 | UP 8621-8670 | 2022-03-30Revision history:
2017-02-06 - Relocated traction motor cables above rear truck (left side) - Minor revisions to cables above front truck (left side) - Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side) 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Revised inverter cabinet grills 2017-12-17 - Removed angled brace behind end plates - Revised cables/pipes under back of cab (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
EMD SD70ACe ← → | 2011-08 - 2016 | 2f | UP 8671-9061 | 2022-03-30Revision history:
2017-02-06 - Relocated traction motor cables above rear truck (left side) - Minor revisions to cables above front truck (left side) - Minor correction to rear edge of panel behind inverter cabinet (below grabirons) (left side) 2017-09-19 - Revised truck traction pin (near center axle on trucks) - Added minor truck details (bolts under axles and pins at radial-steering arm ends) - Smaller radiator fan diameter and spacing, fans moved rearward - Added missing section of air pipe behind front steps (left side) - Revised inverter cabinet grills 2017-11-11 - Relocated hole below handbrake wheel (right side) 2017-12-17 - Revised cables/pipes under back of cab (right side) 2020-12-22 - Increased handrail thickness 2021-01-11 - Fuel tank height and gap from underframe 2022-01-21 - Added missing portion of brake levers near brake cylinders - Corrected line glitch above cab nose door (right side) 2022-03-30 - Coupler cut levers - Corner handrail end plate attachment points | |
EMD SD70M ← → | 2000-04 - 2000-11 | 1e | UP 4000-4278 | 2023-01-19 | |
EMD SD70M ← → | 2000-12 - 2001-10 | 1f | UP 4279-4634, 4640-4709 | 2023-01-19 | |
GE AC4400CW ← → | 1994-08 | 1a1 | UP 9997-9999 | re# 6700-6702 | 2022-11-11Revision history:
2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side view) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE AC4400CW ← → | 1995-10 - 1995-11 | 1b | UP 6838-6866 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers and brackets - Revised front traction motor cable bracket - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side view) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE AC4400CW ← → | 1995-11 | 1c1 | UP 6867-6884 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers and brackets - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side view) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE AC4400CW ← → | 1995-11 | 1c1 | UP 6885-6887 | Built with self-steering trucks; later equipped with Hi-Ad trucks (same as UP 6867-6884) | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers and brackets - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions |
GE AC4400CW ← → | 1996-03 - 1996-06 | 1c2 | UP 6738-6837 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers and brackets - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side view) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE AC4400CW ← → → → | 1997-03 - 1997-06 | 1d, 1e1 | GECX 4000-4009; UP 6550-6565, 6566-6624, 6625-6635 | UP 6635 had rearward left cab vent as on Phase 1e2 and later units | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts |
GE AC4400CW ← → | 1997-06 - 1997-08 | 1e2 | UP 6636-6699 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← → | 1997-10 - 1997-12 | 1e2 | UP 7080-7100 | 2022-11-11Revision history:
2017-02-08 - Narrower 2 rear intakes on conductor's side below radiators - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← → | 1998-06 - 1998-08 | 1g1 | UP 7101-7137 | 2022-11-11Revision history:
2017-02-08 - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added sideframe holes below cab sub-base - Corrected handrail around inverter cabinet 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-11-11 - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← → → | 1999-04 - 1999-08 | 1g2 | UP 7143-7191, 7192-7244 | 2022-11-11Revision history:
2017-02-08 - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added sideframe holes below cab sub-base - Corrected handrail around inverter cabinet 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-05 - Added numberboard latches 2022-11-11 - Removed numberboard hinges - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← → → | 1999-03 - 2000-11 | 2a1 | UP 6430-6549, 6995-6999, 7138-7142, 7245-7297 | 2022-11-11Revision history:
2017-02-08 - Removed truck yaw dampers (but with brackets installed) - Revised front traction motor cable bracket (behind where front yaw damper was located) - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added X-panel under central air intake (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-05 - Added numberboard latches 2022-11-11 - Removed numberboard hinges - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← ← → | 2001-01 - 2002-02 | 2a2 | UP 5700-5809, 5811-5813 | 2022-11-11Revision history:
2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added X-panel under central air intake (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-05 - Added numberboard latches 2022-11-11 - Removed numberboard hinges - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE AC4400CW ← → | 2001-02 - 2002-12 | 2b | UP 5810, 5814-5913 | Plate between air reservoirs present on late Phase 2a2 units | 2022-11-11Revision history:
2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added X-panel under central air intake (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-05 - Added numberboard latches 2022-11-11 - Removed numberboard hinges - Coupler cut lever and pilot details - Corner handrail and step bolts |
GE AC4400CW ← ← → | 2003-01 - 2004-12 | 2c | UP 5554-5694, 5914-5981, 5982-6081 | 2022-11-11Revision history:
2017-02-08 - Added empty handbrake chain bracket to front right truck 2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) (right side) 2020-10-20 - Added missing truck brake piping (left side) - Added X-panel under central air intake (left side) - Added sideframe holes below cab sub-base 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-05 - Added numberboard latches 2022-11-11 - Removed numberboard hinges - Coupler cut lever and pilot details - Corner handrail and step bolts | |
GE Dash 8-40CW ← → | 1989-12 - 1990-03 | 1a | UP 9356-9405 | 2022-11-18Revision history:
2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | |
GE Dash 8-40CW ← → | 1990-11 - 1991-10 | 1b | UP 9406-9480 | 2022-11-18Revision history:
2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | |
GE Dash 8-41CW ← → | 1993-08 - 1993-12 | 1e | UP 9481-9559 | 2022-11-18Revision history:
2021-01-05 - Increased corner handrail thickness - Revised end handrail stanchions - Revised corner handrail location and attachments 2022-11-18 - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions - Cab door window height | |
GE Dash 9-44CW ← → | 1994-07 - 1994-08 | 1c | UP 9700-9739 | 2022-11-12Revision history:
2017-02-18 - Corrected location of 3rd handrail stanchion from rear and rear air pipe vent valve (immediately under stanchion) 2017-02-25 - Replaced 2 X-panels ahead of front air intake with single larger X-panel 2017-09-30 - Removed incorrect line under bell 2020-10-20 - Revised truck brake piping - Reversed orientation of truck brake hose (right-side) 2021-01-04 - Increased corner handrail thickness - Revised end handrail stanchions - Added / revised X-panels in front hood section 2022-11-12 - Cab door window height - Coupler cut lever and pilot details - Corner handrail and step bolts - Horn manifold and back cap dimensions | |
GE ES44AC ← → | 2006-06 - 2006-07 | 1f1 | UP 5325-5347 | 2022-11-29Revision history:
2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard latches - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Added AEI tag above left rear truck | |
GE ES44AC ← → → | 2007-01 - 2007-05 | 1f2 | UP 7600-7622, 7623-7677 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left-side) 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard latches - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Added AEI tag above left rear truck | |
GE ES44AC ← → | 2007-05 - 2007-09 | 2b | UP 7678-7799 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left-side) 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard latches - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ES44AC ← → | 2008-04 - 2008-06 | 2c | UP 7800-7924 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left-side) 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ES44AC ← → → | 2009-01 - 2009-07 | 2d1, 2d2 | UP 7345-7469 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left-side) 2021-01-06 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ES44AC ← → | 2011-04 - 2012-09 | 2f1 | UP 7470-7529, 7925-8051 | 2022-11-29Revision history:
2019-08-12 - Corrected minor transparency issue in radiators (left side) 2020-01-14 - Revised grabirons behind cab (left-side) - Revised wide handrail stanchions 2021-01-12 - Increased corner handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct - Added missing sight glass under right side radiators 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ES44AC ← → → | 2013-06 - 2014-12 | 2f2 | UP 8052-8111, 8112-8267 | 2022-11-29Revision history:
2019-08-12 - Corrected minor transparency issue in radiators (left side) 2020-01-14 - Revised grabirons behind cab (left-side) - Revised wide handrail stanchions - Thinner side handrails 2021-01-12 - Increased corner and side handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct - Added missing sight glass under right side radiators 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ES44AC ← → | 2015-02 - 2016-12 | 2g | UP 2520-2569, 2740-2769 | 2022-11-29Revision history:
2020-01-14 - Revised grabirons behind cab (left-side) - Revised wide handrail stanchions - Thinner side handrails 2021-01-12 - Increased corner and side handrail thickness - Revised end handrail stanchions 2022-01-09 - Added numberboard seam - Corrected line glitch on right front / left rear traction motor air duct 2022-11-12 - Coupler cut lever and pilot details - Corner handrail and step bolts - Added missing truck brake piping (left side) 2022-11-28 - Corner step height - Added AEI tag above left rear truck | |
GE ET44AC ← → | 2015-09 - 2015-12 | UP 2570-2669 | 2022-11-28 | ||
GE ET44AC ← → | 2016-07 - 2016-09 | UP 2670-2739 | 2022-11-29 |
1:36 Drawings
Model | Built | Phase | Numbers | Notes |
---|---|---|---|---|
EMD DDA40X ← → | 1969-04 - 1969-06 | UP 6900-6902 | ||
EMD DDA40X ← → | " | " | as modified | |
EMD DDA40X ← → | 1969-07 - 1969-12 | UP 6903-6924 | ||
EMD DDA40X ← → | " | " | as modified | |
EMD DDA40X ← → | 1970-06 - 1971-09 | UP 6925-6946 | ||
EMD DDA40X ← → | " | " | as modified | |
EMD DDA40X ← → | " | UP 6936 | as modified | |
EMD GP40X ← → | 1977-12 | UP 9000 | HT-B trucks | |
EMD GP40X ← → | " | UP 90 | as modified ex-UP 9000 | |
EMD GP40X ← → | 1978-03 | UP 9001-9005 | HT-B trucks | |
EMD GP40X ← → | " | UP 91-95 | as modified ex-UP 9001-9005 | |
EMD SD24 ← → | 1959-07 - 1959-09 | UP 400-429 | ||
EMD SD24B ← → | 1959-07 - 1959-09 | UP 400B-444B | ||
EMD SD40-2 ← → → | 1972-01 - 1973-06 | 1a1, 1a2 | UP 3123-3239, 8000-8002 | 8000-8002 re#3240-3242 |
EMD SD40-2 ← → | 1974-06 - 1975-03 | 1a2 | UP 3243-3297 | 116" short hood |
EMD SD40-2 ← → | 1975-04 | 1a2 | UP 3298-3304 | 116" short hood |
EMD SD40-2 ← → | 1976-07 - 1976-09 | 1c2 | UP 8035-8064 | 116" short hood re# 3305-3334 |
EMD SD40-2 ← → → | 1977-02 - 1977-05 | 2a1, 2a2 | UP 3335-3399, 8065-8074 | 116" short hood 8065-8074 re#3400-3409 |
EMD SD40-2 ← → | 1978-03 | 2a4 | UP 3410-3415 | 116" short hood |
EMD SD40-2 ← → | 1978-03 - 1978-05 | 2a4 | UP 3416-3488 | 116" short hood |
EMD SD40-2 ← → | 1978-12 - 1979-07 | 2b1, 2b2 | UP 3489-3583, 8075-8099 | 8075-8099 re# 3584-3608 |
EMD SD40-2 ← → | 1979-09 - 1979-12 | 2b2 | UP 3609-3658 | |
EMD SD40-2 ← → | 1980-01 - 1980-11 | 2c1, 2c2 | UP 3659-3804 | |
EMD SD40-2S ← → | 1980-11 | 2c2 | UP 3805-3808 | |
EMD SD50 ← → | 1984-08 - 1984-09 | 2b2 | DRGW 5501-5517 | |
EMD SD50 ← → | " | " | " (SP/UP version) | ex-DRGW |
EMD SD70ACe ← → | 2005-01 - 2005-07 | 2a2 | UP 8309-8423, 1982, 1983, 1988, 4141 | HTCR-4 trucks |
EMD SD70ACe ← → | 2006-05 - 2006-08 | 2c | UP 8424-8520, 1989, 1995, 1996 | HTCR-4 trucks |
EMD SD70ACe ← → | 2007-02 - 2007-07 | 2d1 | UP 8521-8620 | HTCR-4 trucks |
EMD SD70ACe ← → | 2008-05 - 2008-08 | 2e | UP 8621-8670 | HTCR-4 trucks Isolated cab |
EMD SD70M ← → | 2000-04 - 2000-11 | 1e | UP 4000-4278 | |
EMD SD70M ← → | 2000-12 - 2001-10 | 1f | UP 4279-4634, 4640-4709 | |
EMD SD70M ← → | 2000-11 - 2001-01 | 2a | UP 4635-4639 | |
EMD SD70M ← → | 2001-12 | 2b1 | UP 4850-4854 | |
EMD SD70M ← → | 2001-12 - 2002-02 | 2b2 | UP 4855-4879 | |
EMD SD70M ← → | 2002-01 | 2c1 | UP 4710-4726 | |
EMD SD70M ← → | 2002-01 - 2002-08 | 2c2 | UP 4727-4816, 4880-5024 | |
EMD SD70M ← → → | 2001-12 - 2002-10 | 2d1 | UP 4817-4836, 5025-5057, 5103-5108 | |
EMD SD70M ← → | 2002-09 - 2002-11 | 2d1 | UP 5058-5102, 5109-5126 | |
EMD SD70M ← → | 2002-03 | 2d2 | UP 4837-4839 | |
EMD SD70M ← → | 2002-03 - 2002-11 | 2e1 | UP 3971-3973, 4840-4849 | |
EMD SD70M ← → | 2003-01 - 2003-04 | 2e2 | UP 3874-3927 | |
EMD SD70M ← → | 2003-04 - 2004-06 | 2f | UP 3779-3873, 3928-3970 | |
EMD SD70M ← → | 2004-09 - 2004-12 | 2h | UP 5127-5231 | |
GE AC4400CW ← → | 2000-01 - 2000-11 | 2a | UP 6430-6549, 6995-6999, 7245-7297 | |
GE AC4400CW ← ← → | 2001 - 2002 | 2a | UP 5700-5809, 5811-5813 | |
GE AC4400CW ← → | 2002 | 2b | UP 5810, 5814-5913 | |
GE AC4400CW ← ← → | 2003-01 - 2004-12 | 2c | UP 5554-5694, 5914-5981, 5982-6081 | |
GE Dash 8-40C ← → | 1987-11 - 1989-02 | UP 9100-9355 | ||
GE Dash 8-40CW ← → | 1989-12 - 1990-03 | 1a | UP 9356-9405 | |
GE Dash 8-40CW ← → | 1990-11 - 1991-01 | 1b | UP 9406-9480 | |
GE Dash 8-41CW ← → | 1993-08 - 1993-12 | 1e | UP 9481-9559 | |
GE ES44AC ← → | 2003-01 - 2003-02 | 1a | UP 5695-5699 | re# 5348-5352 |
GE ES44AC ← → | 2005-01 - 2005-08 | 1c1 | UP 5353-5553 | |
GE ES44AC ← ← → | 2006-02 - 2006-06 | 1e | UP 5248-5324 | |
GE ES44AC ← → | 2006-06 - 2006-07 | 1f1 | UP 5325-5347 | |
GE ES44AC ← → → | 2007-01 - 2007-05 | 1f2 | UP 7600-7677 | |
GE ES44AC ← → | 2007-05 - 2007-09 | 2b | UP 7678-7799 | |
GE ES44AC ← → | 2008-02 - 2008-05 | 2c | UP 7800-7924 | |
GE ES44AC ← → | 2009 | 2d | UP 7345-7469 | |
GE ES44AC ← → | 2011 | 2e | UP 7470-7529 |
1:55 Drawings
Model | Phase | Numbers | Notes | Accuracy |
---|---|---|---|---|
EMD GP15-1 ← → | UP 1555-1574 | ex-MP | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15-1 ← → | " | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15-1 ← → | UP 1574-1614 | ex-MP | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15-1 ← → | " | " | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15-1 ← → | UP 1615-1644 | ex-MP | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15-1 ← → | UP 1645-1715 | ex-MP | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP15AC ← → | UP 1715-1744 | ex-MP | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP20 ← → | 1a | UP 700-729 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP30 ← → | 1b2 | UP 800-874 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP30 ← → | 1d | UP 700-734 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP30B ← → | UP 700B-726B | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP30B ← → | UP 727B-739B | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD GP35 ← → | 1b1 | UP 740-761 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP38-2 ← → | CP 4522-4524 | ex-UP GP40X rebuild | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP38-2 ← → | 1b | UP 2000-2039 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP38-2 ← → | 1b | UP 2040-2059 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD GP40X ← → | UP 9000-9005 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD24 ← → | UP 400-429 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD24B ← → | UP 400B-444B | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD40 ← → | 1a3 | UP 3000-3039 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40 ← → | 1b1 | UP 3048-3082 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40 ← → | 2c | UP 3083-3122 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2 ← → | 1a1, 1a2 | UP 3123-3239, 8000-8002 | 8000-8002 re#3240-3242 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 1a2 | UP 3243-3304 | 116" short hood | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2a1, 2a2 | UP 3335-3399, 8065-8074 | 116" short hood 8065-8074 re#3400-3409 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2a4 | UP 3410-3488 | 116" short hood | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2b1, 2b2 | UP 3489-3583, 3609-3658, 8075-8099 | 8075-8099 re# 3584-3608 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD40-2 ← → | 2c1, 2c2 | UP 3659-3804 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD40-2S ← → | 2c2 | UP 3805-3808 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD60 ← → | UP 6000-6084 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
EMD SD60M ← ← → | 1a, 1b | UP 6085-6109, 6110-6215 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD60M ← → | 1d | UP 6216-6268 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD60M ← → | 2b | UP 6269-6365 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70ACe ← ↑ → | 2a2 | UP 1982, 1988, 1989, 4141, 8309-8423 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70ACe ← ↑ → | 2c | UP 1989, 1995, 1966, 8424-8520 | Top view includes 8521-8620 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
EMD SD70ACe ← → | 2d1 | UP 8521-8620 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 1e | UP 4000-4278 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 1f | UP 4279-4634, 4640-4709 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2a, 2b | UP 4635-4639, 4850-4879 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2c2 | UP 4727-4816, 4880-5024 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2d2, 2e1 | UP 3971-3973, 4837-4849 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2e2 | UP 3874-3927 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2f | UP 3779-3873, 3928-3970 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD70M ← → | 2h | UP 5127-5231 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
EMD SD90MAC ← → | UP 8000-8308 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE AC4400CW ← → | 1b | UP 6838-6866 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE AC4400CW ← → → | 1c, 1d | UP 6550-6699, 6738-6837, 6867-6887, 7080-7297 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE AC4400CW ← ← ← → | 2a, 2b, 2c | UP 5554-5694, 5700-6081, 6430-6549 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE AC6000CW ← → | UP version 1 | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE AC6000CW ← → | UP version 2 | *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE C30-7 ← → | 1 | UP 2400-2429 | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE C30-7 ← → | 1 | UP 2430-2459 | Adirondack FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE C30-7 ← → | " | " | Rockwell FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE C30-7 ← → | 2a | UP 2460-2499 | Adirondack FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE C30-7 ← → | " | " | Rockwell FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE C30-7 ← → | 2b | UP 2500-2539 | Adirondack FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE C30-7 ← → | " | " | Rockwell FB-3 trucks | * * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE Dash 8-40C ← → | UP 9100-9355 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE Dash 8-40CW ← → | 1 | UP 9356-9480 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | |
GE ES44AC ← → | UP 5695-5699 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE ES44AC ← → | UP 5354-5553 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) | ||
GE U30C ← → | 2f | UP 2810-2829 | Adirondack trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | " | " | GSC trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | 2g1, 2g2 | UP 2830-2904 | Adirondack trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | " | " | GSC trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | 2h1 | UP 2905-2919 | Adirondack trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | " | " | GSC trucks | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
GE U30C ← → | 2h2 | UP 2920-2959 | * *Accuracy legend for 1:55 drawings:
* * * 2007-2008 drawings (mostly accurate) * * 2005-2007 drawings (generally accurate) * 2000-2004 drawings (not dimensionally accurate) |
See also: